LEDE Project

Welcome to the LEDE Project bug reporting and issue tracking system

Problems to be reported here are for the LEDE Project targets, sources, toolchain, core packages, build procedures, distribution and infrastructure. Guidelines for submitting a good bug report can be found at the LEDE Project website. Problems related to LuCI or OpenWrt/LEDE packages need to be reported in their repositories:

Notifications of all submissions and task changes are sent to lede-bugs@infradead.org.

OpenedIDCategoryTask TypePrioritySeveritySummary  descReported InStatus
10.06.2017836KernelBug ReportVery LowMediumZBT-WG3526 low wifi (2.4GHz) speedTrunkUnconfirmed Task Description

Hello.
Device ZBT-WG3526 (16Mb)
Software
Trunk LEDE Reboot SNAPSHOT r4362-5e4bb47 / LuCI Master (git-17.158.76358-75c8eba) (June 9, 2017)
Pakages

kmod-mt76-core - 4.4.71+2017-05-30-ef5b045d-1
kmod-mt7603 - 4.4.71+2017-05-30-ef5b045d-1
kmod-mt76x2 - 4.4.71+2017-05-30-ef5b045d-1

Steps to reproduce

  1. Choose a free channel, I have this channel 13

- Settings in the firmware, channel 13, band 40 MHz, type n.
- The distance between the laptop and the router is 1 meter.

Maximum connection speed 72 MB

On the factory old core (~ 3.3 ver), the connection speed was 150 mbps

21.10.20171095KernelBug ReportVery LowLowYouku YK1 constantly rebootslede-17.01Unconfirmed Task Description

After downloading and flashing latest stable firmware router constantly reboots.

Boot log:

Starting kernel at 0x80000000...

[    0.000000] Linux version 4.4.92 (buildbot@debian8) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3557-a5e1f7f) ) #0 Mon Oct 16 22:57:05 2017
[    0.000000] Board has DDR2
[    0.000000] Analog PMU set to hw control
[    0.000000] Digital PMU set to hw control
[    0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[    0.000000] MIPS: machine is YOUKU YK1
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=0007742a
[    0.000000] Readback ErrCtl register=0007742a
[    0.000000] Memory: 125924K/131072K available (3017K kernel code, 147K rwdata, 384K rodata, 156K init, 208K bss, 5148K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:256
[    0.000000] CPU Clock: 580MHz
[    0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[    0.000000] systick: enable autosleep mode
[    0.000000] systick: running - mult: 214748, shift: 32
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[    0.000012] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[    0.015458] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[    0.080615] pid_max: default: 32768 minimum: 301
[    0.089936] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.102951] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.123433] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.142917] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.155060] pinctrl core: initialized pinctrl subsystem
[    0.166701] NET: Registered protocol family 16
[    0.180868] Can't analyze schedule() prologue at 8000acdc
[    0.204914] rt2880_gpio 10000600.gpio: registering 24 gpios
[    0.215940] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[    0.228377] rt2880_gpio 10000638.gpio: registering 16 gpios
[    0.239356] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[    0.251776] rt2880_gpio 10000660.gpio: registering 32 gpios
[    0.262750] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[    0.275179] rt2880_gpio 10000688.gpio: registering 1 gpios
[    0.285984] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[    0.299494] clocksource: Switched to clocksource systick
[    0.311245] NET: Registered protocol family 2
[    0.320869] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.334648] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.347237] TCP: Hash tables configured (established 1024 bind 1024)
[    0.359961] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.371501] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.384187] NET: Registered protocol family 1
[    0.397136] rt-timer 10000100.timer: maximum frequency is 1220Hz
[    0.409949] Crashlog allocated RAM at address 0x3f00000
[    0.436700] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.448213] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.470333] io scheduler noop registered
[    0.477978] io scheduler deadline registered (default)
[    0.488513] ralink-usb-phy usbphy: invalid resource
[    0.498707] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.514889] console [ttyS0] disabled
[    0.521935] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[    0.541613] console [ttyS0] enabled
[    0.541613] console [ttyS0] enabled
[    0.555428] bootconsole [early0] disabled
[    0.555428] bootconsole [early0] disabled
[    0.578039] spi spi0.0: force spi mode3
[    0.586315] m25p80 spi0.0: mx25l25635e (32768 Kbytes)
[    0.596457] 4 ofpart partitions found on MTD device spi0.0
[    0.607390] Creating 4 MTD partitions on "spi0.0":
[    0.616948] 0x000000000000-0x000000030000 : "u-boot"
[    0.628660] 0x000000030000-0x000000040000 : "u-boot-env"
[    0.641195] 0x000000040000-0x000000050000 : "factory"
[    0.653145] 0x000000050000-0x000002000000 : "firmware"
[    0.920855] rt2880-pinmux pinctrl: pin io40 already requested by pinctrl; cannot claim for 10100000.ethernet
[    0.940519] rt2880-pinmux pinctrl: pin-40 (10100000.ethernet) status -22
[    0.953884] rt2880-pinmux pinctrl: could not request pin 40 (io40) from group ephy  on device rt2880-pinmux
[    0.973306] mtk_soc_eth 10100000.ethernet: Error applying setting, reverse things back
[    0.991740] gsw: setting port4 to ephy mode
[    1.000343] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[    1.012961] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[    1.029991] rt2880_wdt 10000120.watchdog: Initialized
[    1.041552] NET: Registered protocol family 10
[    1.053816] NET: Registered protocol family 17
[    1.062826] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    1.087976] 8021q: 802.1Q VLAN Support v1.8
[    1.099280] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[    1.114259] Please append a correct "root=" boot option; here are the available partitions:
[    1.130917] 1f00             192 mtdblock0  (driver?)
[    1.140996] 1f01              64 mtdblock1  (driver?)
[    1.151073] 1f02              64 mtdblock2  (driver?)
[    1.161150] 1f03           32448 mtdblock3  (driver?)
[    1.171223] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[    1.188740] Rebooting in 1 seconds..
18.10.20171075Base systemBug ReportVery LowLowxiaomi mini hardware/power issuesTrunkUnconfirmed Task Description

i’ve noticed recently there is a signal drop on mini when used legacy wifi mode. this mode disables chain1 in mtk driver and use only chain0. i’ve made detailed test of both firmware with 3 different cards. can somebody else try the same test to conclude if it is power configuration issue or hardware damage?

TX values are card TX which means RSSI from router while RX values are mini’s txpower levels received by cards.

AR9271 is AWUS036NHA with 10dB comfast antenna
RT5370 is EDUP 150N mini usb adapter
AR9462 is minipci card
NC means card did not detect beacons in this mode

TX/RX path configuration was changed within eeprom offset 0×34

test results:

MTK			2T1R		OpenWrt

G	N20	N40			G	N20	N40

-25	-25	-25	AR9271 TX	-47	-47	-47
-61	-48	-48	AR9271 RX	-52	-52	-52

NC	-25	-25	RT5370 TX	-50	-50	-50
NC	-29	-29	RT5370 RX	-33	-33	-37

-25	-25	-25	AR9462 TX	-41	-45	-45
-40	-25	-25	AR9462 RX	-35	-35	-35

MTK			1T2R		OpenWrt

G	N20	N40			G	N20	N40

-78	-78	-78	AR9271 TX	-47	-47	-47
-70	-70	-70	AR9271 RX	-75	-75	-75

-79	-79	-79	RT5370 TX	-50	-50	-50
-59	-59	-59	RT5370 RX	-59	-59	-59

-78	-78	-78	AR9462 TX	-43	-45	-45
-45	-45	-45	AR9462 RX	-50	-50	-50

MTK			1T1R		OpenWrt

G	N20	N40			G	N20	N40

-25	-25	-25	AR9271 TX	-47	-47	-47
-70	-70	-70	AR9271 RX	-75	-75	-75

-25	-25	-25	RT5370 TX	-50	-50	-50
-59	-59	-59	RT5370 RX	-59	-59	-59

-23	-23	-23	AR9462 TX	-43	-45	-45
-45	-45	-45	AR9462 RX	-50	-50	-50

MTK			2T2R		OpenWrt

G	N20	N40			G	N20	N40

-46	-46	-46	AR9271 TX	-37	-37	-37
-70	-48	-48	AR9271 RX	-52	-52	-52

-44	-44	-47	RT5370 TX	-33	-33	-39
-59	-29	-29	RT5370 RX	-35	-33	-37

-40	-45	-47	AR9462 TX	-35	-37	-39
-45	-25	-25	AR9462 RX	-35	-35	-35
13.11.20171167Base systemBug ReportVery LowLowXiaomi Mi R3GTrunkUnconfirmed Task Description

I warmly welcome.

I have an unusual problem.
I have uploaded a new image to the router, and after a few minutes I lost 2.4.
I have configured two networks on my hardware.
The networks 5G and 2.4G.
Both as AES, nothing more on the router is not fired.
The network disappears completely, turning off and re-enabling the card by Luci’s panel gives nothing. The network is still not visible. I can not connect to it either by selecting: Hidden Network in Windows 10.
Do you have any suggestions / solutions?
PS. Having an abgn card I am pulling in a transfer of around 42Mb in tests, but the internet has 80Mb, and after the cable so many in the test comes out.
What’s going on? I have inserted various cards, and to PCI and USB.

PCI: Intel 5100
USB: Netgear WNDA3100v3

18.02.2017532Base systemBug ReportVery LowMediumXiaomi mi nano (miwifi nano) unstable as WiFi Repeaterlede-17.01Unconfirmed Task Description

I run version 17.01.0-rc2 on my Xiaomi mi nano (https://lede-project.org/toh/hwdata/xiaomi/xiaomi_miwifi_nano)

I want to use it as wireless repeater with extra SSID (i think someone call it WISP client).

The miwifi is connected to my home wifi. And my device is connected to the SSID provided by the miwifi nano (no LAN connection).

If i do a speed test or download a large file to test the connection speed, the speed drops to a very low rate after some seconds. On the serial console i can see a call trace at this moment. After this, i have to reboot the miwifi nano to get a working WAN connection.

I will attach the serial console output. Hope that helps.

Tested with LAN connected was stable and fast.

drombo

15.07.2017908KernelBug ReportMediumLowx86: Xen support broken in 17.01.2 and laterlede-17.01Researching Task Description

Testing the x86/generic image with Xen 4.5:

  • 17.01.0: works
  • 17.01.1: works
  • 17.01.2: fails to boot
  • latest lede-17.01 r3466-f6907dcc79: fails to boot
  • latest trunk r4553-a89c36b: works

When the kernel fails to boot, xl prints this:

xc: error: elf_xen_note_check: ERROR: Will only load images built for the generic loader or Linux images (Not '' and ''): Invalid kernel
libxl: error: libxl_dom.c:414:libxl__build_pv: xc_dom_parse_image failed: No such file or directory
libxl: error: libxl_create.c:1024:domcreate_rebuild_done: cannot (re-)build domain: -3

It means that the kernel image has no Xen support (or there is an issue with the support).

Given the changes between 17.01.1 and 17.01.2, I think the patch adding PAE support may be responsible.

This was first reported in FS#787.

05.10.20171041Base systemBug ReportVery LowLowWZR-600DHP: Nexus 5X can not connect with HT40 + channe...lede-17.01Unconfirmed Task Description

At least my Raspberry Pi, Moto E LTE, and Chromebooks had no problems with it. Only the Nexus 5X couldn’t connect AFAIK.

Either way, channel 3 works, but channel 1 did not work, connecting from my Nexus 5X. With channel 1 HT40, it associates, but its DHCP DISCOVER packets are not seen by the router.

Channel 1 with HT20 does work fine also.

16.10.20171064Base systemBug ReportVery LowLowWXR-1900DHP Problems with 17.01.2 and 17.01.3 (BCM53xx)TrunkUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on
Buffalo WXR-1900DHP

- Software versions of LEDE release, packages, etc.
Stable Release 17.01.2 and 17.01.3 both partially functional. (17.01.01 works well, except wifi)
lede-17.01.2-bcm53xx-buffalo-wxr-1900dhp-squashfs.trx
lede-17.01.3-bcm53xx-buffalo-wxr-1900dhp-squashfs.trx

- Steps to reproduce
1. Flash lede-17.01.1-bcm53xx-buffalo-wxr-1900dhp-squashfs.trx
2. Observe working - luci stats on overview page, PPPoE sucessful connection
3. Flash lede-17.01.2-bcm53xx-buffalo-wxr-1900dhp-squashfs.trx via luci (uncheck preserve settings)
4. Observe issues - luci no stats for memory etc, PPPoE fails to connect after setup.

Please let me know what other information or further testing would be useful.

24.08.2016115Base systemBug ReportVery LowMediumWWAN-connections using 3g with HUAWEI ME909u-521 unstab...TrunkUnconfirmed Task Description

Actually, I am trying to stabilize wwan (3g actually; LTE later on) using pppd with my HUAWEI ME909u-521,
because either my MT7620-based router locks up during boot already; or after short period of real usage.
During night, when router is almost idle, just some watchdog date sent via wwan, no problem.

First trace of a possible problem was this msg in logread:
daemon.notice netifd: wwan (1676): Error setting WWAN mode!

Wich is expected, as in /lib/netifd/proto/3g.sh:

...

                      elif echo "$cardinfo" | grep -qi huawei; then
                              case "$service" in
                                      umts_only) CODE="14,2";;
                                      gprs_only) CODE="13,1";;
                                      *) CODE="2,2";;
                              esac
                              export MODE="AT^SYSCFG=${CODE},3FFFFFFF,2,4"    #####Will not work !!!!! Switching USB-Stick to 3g-preferred ?

...
...

                      [ -n "$MODE" ] && gcom -d "$device" -s /etc/gcom/setmode.gcom

Will not work, because the ME909u-521 rejects AT^SYSCFG . However, AT^SYSCFGEX will work, but having different syntax.
MODE=”AT^SYSCFG=${CODE},3FFFFFFF,2,4” will be effective for simpler modems.

/etc/gcom/setmode.gcom returns exit 1; but this error is not checked in 3g.sh

Not shure, whether this is the reason for my problems; however, reason of concern, as high speed modems
are more and more common.
Willing to participate in testing/debugging.

For details regarding my modem, consult
HUAWEI ME909u-521 LTE LGA Module AT Command Interface Specification
http://www.paoli.cz/out/media/HUAWEI_ME909u-521_LTE_LGA_Module_AT_Command_Interface_Specification-V100R001_02.pdf

19.07.2017915Base systemBug ReportVery LowLowWRT54GS v1.1 Power LED flashes & leds-gpio fails to loa...AllUnconfirmed Task Description

The leds-gpio module fails to load on WRT54GS v1.1 with this error message in the console:
“leds-gpio: probe of leds-gpio failed with error -16” This applies both to OpenWRT 15.05.1 and LEDE 17.01.2 as well as the latest Snapshot.

The nvram variable “boardtype” is 0×0708 on this device.
In leds.c this gets mapped to “bcm47xx_leds_linksys_wrt54g_generic” http://elixir.free-electrons.com/linux/latest/source/arch/mips/bcm47xx/leds.c#L677

With the following layout:

BCM47XX_GPIO_LED(0, "unk", "dmz", 1, LEDS_GPIO_DEFSTATE_OFF),
BCM47XX_GPIO_LED(1, "unk", "power", 0, LEDS_GPIO_DEFSTATE_ON),
BCM47XX_GPIO_LED(5, "white", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
BCM47XX_GPIO_LED(7, "orange", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),

But this layout is invalid because this board does not have the “SecureEasySetup” WPS button.
GPIO5 is used by the reset button, that is why leds-gpio fails with error -16 (Device or resource busy).

As a quick test I changed the “boardtype” to 0×0101, leds-gpio can then load successfully and the power LED no longer flashes.
That layout is however not correct for the WRT54GS, the actual layout is:

Name	GPIO	Polarity
WLAN	0	Active low
POWER	1	Active high
DMZ	7	Active low

The problem in the source is that “boardtype” 0×0708 is not a unique identifier.
That actually matches several WRT54G v2 > v3.1 devices, and apparently also WRT54GS up to revision 2.1 that has the WPS button.
See the following old bug report for a list: https://lists.openwrt.org/pipermail/openwrt-devel/2014-June/025868.html

So the proper fix would be to introduce the variable “boardflags” as well into the code:
http://elixir.free-electrons.com/linux/latest/source/arch/mips/bcm47xx/board.c#L297

It is also worth noting that the reason the Power LED flickers is due to it’s hardware implementation.
The LED can only be on or flashing, the flashing is done by an oscillator on the board itself.
Ref: https://bugs.lede-project.org/index.php?do=details&task_id=793

04.05.2017761Base systemBug ReportVery LowMediumWRT54G image is too big for device.lede-17.01Unconfirmed Task Description

Device: WRT54G v2
Lede version/build: lede-17.01.1-brcm47xx-legacy-linksys-wrt54g-squashfs.bin

The image provided is 4001824 bytes, whereas device flash is 3866624 bytes.
Cannot upload firmware to device.

Source old wiki: https://wiki.openwrt.org/toh/linksys/wrt54g

28.04.2017740Base systemBug ReportVery LowMediumWRT54 Router Power LED continually flasheslede-17.01Unconfirmed Task Description
  • LEDE 17.01.1
  • WRT54G v3 and WRT54GS
  • after installing, power LED continually flashes
  • no noticeable difference in LED between failsafe/actual moment of soft reboot//when router is up
  • I had to failsafe the WRT54G multiple times due to other initial config errors (attempting to bridge wlan0 to LAN, which was possible in another OS), I could only identify failsafe by Pinging it then SSHing quickly
  • The method I described to identify failsafe is not mentioned in documentation
02.11.2016263KernelBug ReportVery LowMediumWRT3200ACM WAN connection failure in under 24 hoursTrunkWaiting on reporter Task Description

Symptom

WAN connectivity is lost until the device is rebooted; failure aligns with stack trace (attached). I’ve observed three failures of this same type, and all have occurred at around 18 hours of device up time. Work-around (yet to be tested) is to schedule a periodic device reboot every 12 hours.

Device problem occurs on

  • Linksys WRT3200ACM (version 1)
  • LEDE configuration is near-stock, with the only modifications being PPPoE configuration and WiFi setup/enable. Issue does not appear to be similar to FS#227 (PPPoE).

Software versions of LEDE release, packages, etc.

Release:

  [0.000000] Linux version 4.4.28 (buildbot@builds) (gcc version 5.4.0 (LEDE GCC 5.4.0 r2062) ) #0 SMP Mon Oct 31 16:13:37 2016
  [0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
  [0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
  [0.000000] Machine model: Linksys WRT3200ACM

Packages:

  Default packages + luci-ssl

Possibly helpful info (80211 related output in log):

  <<Marvell 802.11ac Wireless Network Driver version 10.3.2.0-20161011>>
  pci 0000:00:01.0: enabling device (0140 -> 0142)
  ieee80211 phy0: priv->iobase0 = e0e00000
  ieee80211 phy0: priv->iobase1 = e1080000
  ieee80211 phy0: priv->pcmd_buf = de248000  priv->pphys_cmd_buf = 1e248000
  ieee80211 phy0: fw download start
  ieee80211 phy0: FwSize = 207660 downloaded Size = 207660 curr_iteration 65522
  ieee80211 phy0: fw download complete
  ieee80211 phy0: pcmd = de248000
  ieee80211 phy0: firmware version: 0x7080004
  ieee80211 phy0: firmware region code: 10
  ieee80211 phy0: 2G disabled, 5G enabled
  ieee80211 phy0: 4 TX antennas, 4 RX antennas
  pci 0000:00:02.0: enabling device (0140 -> 0142)
  ieee80211 phy1: priv->iobase0 = e1200000
  ieee80211 phy1: priv->iobase1 = e1480000
  ieee80211 phy1: priv->pcmd_buf = dda20000  priv->pphys_cmd_buf = 1da20000
  ieee80211 phy1: fw download start
  ieee80211 phy1: FwSize = 207660 downloaded Size = 207660 curr_iteration 65527
  ieee80211 phy1: fw download complete
  ieee80211 phy1: pcmd = dda20000
  ieee80211 phy1: firmware version: 0x7080004
  ieee80211 phy1: firmware region code: 10
  ieee80211 phy1: 2G enabled, 5G disabled
  ieee80211 phy1: 4 TX antennas, 4 RX antennas

Steps to reproduce

Device was idle before the stack trace, but logs show some DHCP-related activity within 1 minute prior to the fault.

Stack Trace

Wed Nov  2 17:10:41 2016 kern.err kernel: [74541.045379] ieee80211 phy1: create ba result error 1
Wed Nov  2 17:10:41 2016 kern.err kernel: [74541.059396] ieee80211 phy1: ampdu operation error code: -22
Wed Nov  2 17:10:42 2016 kern.warn kernel: [74542.085673] ------------[ cut here ]------------
Wed Nov  2 17:10:42 2016 kern.warn kernel: [74542.090364] WARNING: CPU: 0 PID: 5305 at compat-wireless-2016-10-08/net/mac80211/agg-tx.c:398 ___ieee80211_stop_tx_ba_session+0x1e8/0x1f8 [mac80211]()
Wed Nov  2 17:10:42 2016 kern.warn kernel: [74542.103914] Modules linked in: pppoe ppp_async iptable_nat pppox ppp_generic nf_nat_ipv4 nf_conntrack_ipv6 nf_conntrack_ipv4 ipt_REJECT ipt_MASQUERADE xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_id xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_CT slhc nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack iptable_raw iptable_mangle iptable_fWed Nov  2 17:10:42 2016 kern.warn kernel: [74542.162765] CPU: 0 PID: 5305 Comm: kworker/u4:2 Not tainted 4.4.28 #0
Wed Nov  2 17:10:42 2016 kern.warn kernel: [74542.169230] Hardware name: Marvell Armada 380/385 (Device Tree)
Wed Nov  2 17:10:42 2016 kern.warn kernel: [74542.175192] Workqueue: phy1 ieee80211_iface_work [mac80211]
Wed Nov  2 17:10:42 2016 kern.warn kernel: [74542.180804] [<c0027d80>] (unwind_backtrace) from [<c0024500>] (show_stack+0x10/0x14)
Wed Nov  2 17:10:42 2016 kern.warn kernel: [74542.188584] [<c0024500>] (show_stack) from [<c021779c>] (dump_stack+0x8c/0xa0)
Wed Nov  2 17:10:42 2016 kern.warn kernel: [74542.195838] [<c021779c>] (dump_stack) from [<c0034e5c>] (warn_slowpath_common+0x94/0xb0)
Wed Nov  2 17:10:42 2016 kern.warn kernel: [74542.203962] [<c0034e5c>] (warn_slowpath_common) from [<c0034f14>] (warn_slowpath_null+0x1c/0x24)
Wed Nov  2 17:10:42 2016 kern.warn kernel: [74542.212799] [<c0034f14>] (warn_slowpath_null) from [<bf0849fc>] (___ieee80211_stop_tx_ba_session+0x1e8/0x1f8 [mac80211])
Wed Nov  2 17:10:42 2016 kern.warn kernel: [74542.223749] [<bf0849fc>] (___ieee80211_stop_tx_ba_session [mac80211]) from [<bf084df0>] (__ieee80211_stop_tx_ba_session+0x2c/0x40 [mac80211])
Wed Nov  2 17:10:42 2016 kern.warn kernel: [74542.236527] [<bf084df0>] (__ieee80211_stop_tx_ba_session [mac80211]) from [<bf089174>] (ieee80211_iface_work+0x1c0/0x610 [mac80211])
Wed Nov  2 17:10:42 2016 kern.warn kernel: [74542.248510] [<bf089174>] (ieee80211_iface_work [mac80211]) from [<c00494a4>] (process_one_work+0x228/0x3bc)
Wed Nov  2 17:10:42 2016 kern.warn kernel: [74542.258292] [<c00494a4>] (process_one_work) from [<c0049948>] (worker_thread+0x310/0x504)
Wed Nov  2 17:10:42 2016 kern.warn kernel: [74542.266505] [<c0049948>] (worker_thread) from [<c004e65c>] (kthread+0xf0/0xf8)
Wed Nov  2 17:10:42 2016 kern.warn kernel: [74542.273758] [<c004e65c>] (kthread) from [<c0009d38>] (ret_from_fork+0x14/0x3c)
Wed Nov  2 17:10:42 2016 kern.warn kernel: [74542.281021] ---[ end trace 09d229b863156d80 ]---
19.04.2017717Base systemBug ReportVery LowHighWRT3200ACM USB 3.0 ProblemAllUnconfirmed Task Description

I canĀ“t get my Seagate Expansion Portable 1TB STEA1000400 USB3.0 drive to be be recognized on the USB 3.0 port of the router after a reboot or cold start on WRT3200 but if i remove and hotplug the drive, it is automatically detected and can be mounted.
It happens with images from Openwrt 15.05.1, LEDE 17.01.1 and many snapshots from both projects that i have installed. I have no problem with another usb2.0 drive from Samsung that is installed in another USB2.0 port.

After Cold START or REBOOT

 root@LEDE:~# dmesg
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.9.20 (ag33e33@ubuntu) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3963-7ae58be) ) #0 SMP Wed Apr 12 16:12:18 2017
[    0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt:Machine model: Linksys WRT3200ACM
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 131072
[    0.000000] free_area_init_node: node 0, pgdat c0646900, node_mem_map dfbf9000
[    0.000000]   Normal zone: 1024 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 131072 pages, LIFO batch:31
[    0.000000] percpu: Embedded 13 pages/cpu @dfbce000 s22732 r8192 d22324 u53248
[    0.000000] pcpu-alloc: s22732 r8192 d22324 u53248 alloc=13*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
[    0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock6 ro rootdelay=1 rootfstype=jffs2 earlyprintk mtdparts=armada-nand:2048K(uboot)ro,128K(u_env),256K(s_env),256K@8064K(devinfo),1920K@8320K(sysdiag),80m@10m(kernel),74m@16m(rootfs),80m@90m(alt_kernel),74m@96m(alt_rootfs),160m@10m(ubifs),-@170m(syscfg)
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 512848K/524288K available (4545K kernel code, 180K rwdata, 1244K rodata, 280K init, 310K bss, 11440K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
                   vector  : 0xffff0000 - 0xffff1000   (   4 kB)
                   fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
                   vmalloc : 0xe0800000 - 0xff800000   ( 496 MB)
                   lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)
                   pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
                   modules : 0xbf000000 - 0xbfe00000   (  14 MB)
                     .text : 0xc0008000 - 0xc0478918   (4547 kB)
                     .init : 0xc05d4000 - 0xc061a000   ( 280 kB)
                     .data : 0xc061a000 - 0xc0647200   ( 181 kB)
                      .bss : 0xc0647200 - 0xc0694a00   ( 310 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] mvebu_mbus: [Firmware Warn]: deprecated mbus-mvebu Device Tree, suspend/resume will not work
[    0.000000] L2C-310 enabling early BRESP for Cortex-A9
[    0.000000] L2C-310 full line of zeros enabled for Cortex-A9
[    0.000000] L2C-310 D prefetch enabled, offset 1 lines
[    0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[    0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB
[    0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001
[    0.000000] Selected CPU frequency (16) unsupported
[    0.000000] Switching to timer-based delay loop, resolution 40ns
[    0.000002] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns
[    0.000008] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
[    0.000114] Calibrating local timer... 933.22MHz.
[    0.060032] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000)
[    0.060037] pid_max: default: 32768 minimum: 301
[    0.060076] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.060079] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.060274] CPU: Testing write buffer coherency: ok
[    0.060365] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.060376] Setting up static identity map for 0x8280 - 0x82d8
[    0.060434] mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4
[    0.060494] mvebu-pmsu: Initializing Power Management Service Unit
[    0.060904] Booting CPU 1
[    0.061041] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.061070] Brought up 2 CPUs
[    0.061075] SMP: Total of 2 processors activated (100.00 BogoMIPS).
[    0.061078] CPU: All CPU(s) started in SVC mode.
[    0.062739] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.062790] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.062796] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.062831] pinctrl core: initialized pinctrl subsystem
[    0.063142] NET: Registered protocol family 16
[    0.063575] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.090041] cpuidle: using governor ladder
[    0.090171] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling
[    0.090177] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling
[    0.120467] reg-fixed-voltage xhci0-vbus: could not find pctldev for node /soc/internal-regs/pinctrl@18000/xhci0-vbus-pins, deferring probe
[    0.120607] SCSI subsystem initialized
[    0.120687] libata version 3.00 loaded.
[    0.120790] usbcore: registered new interface driver usbfs
[    0.120815] usbcore: registered new interface driver hub
[    0.120835] usbcore: registered new device driver usb
[    0.121329] clocksource: Switched to clocksource armada_370_xp_clocksource
[    0.121647] NET: Registered protocol family 2
[    0.121869] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.121890] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.121920] TCP: Hash tables configured (established 4096 bind 4096)
[    0.121941] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.121952] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.122009] NET: Registered protocol family 1
[    0.122021] PCI: CLS 0 bytes, default 64
[    0.122803] Crashlog allocated RAM at address 0x3f00000
[    0.122877] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[    0.124945] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.124953] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.125699] io scheduler noop registered
[    0.125703] io scheduler deadline registered (default)
[    0.126071] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver
[    0.126671] mvebu-pcie soc:pcie-controller: PCI host bridge to bus 0000:00
[    0.126679] pci_bus 0000:00: root bus resource [io  0x1000-0xfffff]
[    0.126683] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[    0.126687] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.126701] pci 0000:00:01.0: [11ab:6820] type 01 class 0x060400
[    0.126784] pci 0000:00:02.0: [11ab:6820] type 01 class 0x060400
[    0.126859] PCI: bus0: Fast back to back transfers disabled
[    0.126864] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    0.126870] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    0.126918] pci 0000:01:00.0: [11ab:2b40] type 00 class 0x020000
[    0.126933] pci 0000:01:00.0: reg 0x10: [mem 0x40000000-0x401fffff 64bit pref]
[    0.126943] pci 0000:01:00.0: reg 0x18: [mem 0x40200000-0x402fffff 64bit pref]
[    0.127002] pci 0000:01:00.0: supports D1 D2
[    0.127005] pci 0000:01:00.0: PME# supported from D0 D1 D3hot D3cold
[    0.127068] PCI: bus1: Fast back to back transfers disabled
[    0.127073] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    0.127132] pci 0000:02:00.0: [11ab:2b40] type 00 class 0x020000
[    0.127151] pci 0000:02:00.0: reg 0x10: [mem 0x42000000-0x421fffff 64bit pref]
[    0.127162] pci 0000:02:00.0: reg 0x18: [mem 0x42200000-0x422fffff 64bit pref]
[    0.127244] pci 0000:02:00.0: supports D1 D2
[    0.127246] pci 0000:02:00.0: PME# supported from D0 D1 D3hot D3cold
[    0.127310] PCI: bus2: Fast back to back transfers disabled
[    0.127315] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[    0.127384] pci 0000:00:01.0: BAR 8: assigned [mem 0xe0000000-0xe02fffff]
[    0.127390] pci 0000:00:02.0: BAR 8: assigned [mem 0xe0400000-0xe06fffff]
[    0.127396] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe01fffff 64bit pref]
[    0.127405] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0200000-0xe02fffff 64bit pref]
[    0.127413] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.127418] pci 0000:00:01.0:   bridge window [mem 0xe0000000-0xe02fffff]
[    0.127425] pci 0000:02:00.0: BAR 0: assigned [mem 0xe0400000-0xe05fffff 64bit pref]
[    0.127434] pci 0000:02:00.0: BAR 2: assigned [mem 0xe0600000-0xe06fffff 64bit pref]
[    0.127443] pci 0000:00:02.0: PCI bridge to [bus 02]
[    0.127448] pci 0000:00:02.0:   bridge window [mem 0xe0400000-0xe06fffff]
[    0.127646] mv_xor f1060800.xor: Marvell shared XOR driver
[    0.181754] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[    0.181840] mv_xor f1060900.xor: Marvell shared XOR driver
[    0.241717] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[    0.241857] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.242621] console [ttyS0] disabled
[    0.262683] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 21, base_baud = 12500000) is a 16550A
[    0.983287] console [ttyS0] enabled
[    0.988691] loop: module loaded
[    0.992090] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[    1.001176] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
[    1.010274] scsi host0: ahci-mvebu
[    1.013847] scsi host1: ahci-mvebu
[    1.017348] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 41
[    1.025306] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 41
[    1.033594] pxa3xx-nand f10d0000.flash: This platform can't do DMA on this device
[    1.041369] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xda
[    1.047747] nand: AMD/Spansion S34ML02G2
[    1.051690] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
[    1.059379] pxa3xx-nand f10d0000.flash: ECC strength 16, ECC step size 2048
[    1.066556] Bad block table found at page 131008, version 0x01
[    1.072752] Bad block table found at page 130944, version 0x01
[    1.078863] 11 ofpart partitions found on MTD device pxa3xx_nand-0
[    1.085074] Creating 11 MTD partitions on "pxa3xx_nand-0":
[    1.090582] 0x000000000000-0x000000200000 : "u-boot"
[    1.095830] 0x000000200000-0x000000220000 : "u_env"
[    1.100951] 0x000000220000-0x000000260000 : "s_env"
[    1.106089] 0x0000007e0000-0x000000820000 : "devinfo"
[    1.111433] 0x000000820000-0x000000a00000 : "sysdiag"
[    1.116797] 0x000000a00000-0x000005a00000 : "kernel1"
[    1.122301] 0x000001000000-0x000005a00000 : "ubi"
[    1.127404] 0x000005a00000-0x00000aa00000 : "kernel2"
[    1.132905] 0x000006000000-0x00000aa00000 : "rootfs2"
[    1.138362] 0x00000aa00000-0x000010000000 : "syscfg"
[    1.143774] 0x000000260000-0x000000820000 : "unused_area"
[    1.149701] libphy: Fixed MDIO Bus: probed
[    1.154064] libphy: orion_mdio_bus: probed
[    1.158297] mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled
[    1.166962] mvneta f1070000.ethernet eth0: Using hardware mac address 60:38:e0:b9:ea:c0
[    1.175959] mvneta f1034000.ethernet eth1: Using random mac address a2:8d:5e:6d:ee:98
[    1.183881] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.190435] ehci-pci: EHCI PCI platform driver
[    1.194928] ehci-platform: EHCI generic platform driver
[    1.200245] ehci-orion: EHCI orion driver
[    1.204336] orion-ehci f1058000.usb: EHCI Host Controller
[    1.209765] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1
[    1.217412] orion-ehci f1058000.usb: irq 37, io mem 0xf1058000
[    1.251329] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
[    1.257480] hub 1-0:1.0: USB hub found
[    1.261254] hub 1-0:1.0: 1 port detected
[    1.265551] usbcore: registered new interface driver usb-storage
[    1.271723] armada38x-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0
[    1.279341] i2c /dev entries driver
[    1.294252] orion_wdt: Initial timeout 171 sec
[    1.298933] sdhci: Secure Digital Host Controller Interface driver
[    1.305146] sdhci: Copyright(c) Pierre Ossman
[    1.362546] ata1: SATA link down (SStatus 0 SControl 300)
[    1.367991] ata2: SATA link down (SStatus 0 SControl 300)
[    1.371354] mmc0: SDHCI controller on f10d8000.sdhci [f10d8000.sdhci] using ADMA
[    1.371428] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.377154] marvell-cesa f1090000.crypto: CESA device successfully registered
[    1.377556] NET: Registered protocol family 10
[    1.391590] NET: Registered protocol family 17
[    1.391604] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    1.391605] 8021q: 802.1Q VLAN Support v1.8
[    1.391661] Registering SWP/SWPB emulation handler
[    1.392791] xhci-hcd f10f8000.usb3: xHCI Host Controller
[    1.392803] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 2
[    1.392861] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010
[    1.392881] xhci-hcd f10f8000.usb3: irq 44, io mem 0xf10f8000
[    1.393134] hub 2-0:1.0: USB hub found
[    1.393160] hub 2-0:1.0: 1 port detected
[    1.393247] xhci-hcd f10f8000.usb3: xHCI Host Controller
[    1.393253] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 3
[    1.393292] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[    1.393478] hub 3-0:1.0: USB hub found
[    1.393501] hub 3-0:1.0: 1 port detected
[    1.393820] UBI: auto-attach mtd6
[    1.393824] ubi0: attaching mtd6
[    1.397930] random: fast init done
[    1.401551] mmc0: new high speed SDIO card at address 0001
[    1.593092] ubi0: scanning is finished
[    1.601334] ubi0: attached mtd6 (name "ubi", size 74 MiB)
[    1.606756] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.613664] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.620479] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.627475] ubi0: good PEBs: 592, bad PEBs: 0, corrupted PEBs: 0
[    1.633508] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[    1.640759] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1419003487
[    1.649932] ubi0: available PEBs: 0, total reserved PEBs: 592, PEBs reserved for bad PEB handling: 40
[    1.659197] ubi0: background thread "ubi_bgt0d" started, PID 668
[    1.659208] usb 1-1: new high-speed USB device number 2 using orion-ehci
[    1.659643] block ubiblock0_0: created from ubi0:0(rootfs)
[    1.659645] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[    1.659829] mvsw61xx 10.mvsw61xx: Found MV88E6352 at f1072004.mdio-mi:10
[    1.659832] mvsw61xx 10.mvsw61xx: Using direct addressing
[    1.671972] armada38x-rtc f10a3800.rtc: setting system clock to 2101-11-05 12:45:50 UTC (4160637950)
[    1.705850] Waiting 1 sec before mounting root device...
[    1.852932] usb-storage 1-1:1.0: USB Mass Storage device detected
[    1.859142] scsi host2: usb-storage 1-1:1.0
[    2.722974] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    2.730260] Freeing unused kernel memory: 280K (c05d4000 - c061a000)
[    2.736655] This architecture does not have kernel memory protection.
[    2.855724] init: Console is alive
[    2.859203] init: - watchdog -
[    2.924338] scsi 2:0:0:0: Direct-Access     Samsung  S2 Portable           PQ: 0 ANSI: 2 CCS
[    3.111498] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    3.151660] sd 2:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB)
[    3.159777] sd 2:0:0:0: [sda] Write Protect is off
[    3.164597] sd 2:0:0:0: [sda] Mode Sense: 28 00 00 00
[    3.165152] sd 2:0:0:0: [sda] No Caching mode page found
[    3.170490] sd 2:0:0:0: [sda] Assuming drive cache: write through
[    3.179038]  sda: sda1
[    3.183653] sd 2:0:0:0: [sda] Attached SCSI disk
[    3.188738] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    3.195221] ohci-platform: OHCI generic platform driver
[    3.200902] uhci_hcd: USB Universal Host Controller Interface driver
[    3.207556] ohci-pci: OHCI PCI platform driver
[    3.212156] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    3.228593] init: - preinit -
[    3.422394] mvneta f1070000.ethernet tmp0: renamed from eth0
[    3.462586] mvneta f1034000.ethernet eth0: renamed from eth1
[    3.512510] mvneta f1070000.ethernet eth1: renamed from tmp0
[    3.833291] mvneta f1034000.ethernet eth0: configuring for fixed link mode
[    3.840562] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    3.846607] mvneta f1034000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[    3.854578] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    5.909798] mount_root: loading kmods from internal overlay
[    5.921475] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[    5.929503] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[    6.328768] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 806
[    6.357145] UBIFS (ubi0:1): recovery needed
[    6.403932] random: crng init done
[    6.431762] UBIFS (ubi0:1): recovery completed
[    6.436249] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[    6.444117] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    6.454076] UBIFS (ubi0:1): FS size: 61329408 bytes (58 MiB, 483 LEBs), journal size 3047424 bytes (2 MiB, 24 LEBs)
[    6.464556] UBIFS (ubi0:1): reserved for root: 2896739 bytes (2828 KiB)
[    6.471198] UBIFS (ubi0:1): media format: w4/r0 (latest is w4/r0), UUID DEE50754-EFFE-4990-A7A6-C97266C9BEF0, small LPT model
[    6.483473] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[    6.493882] block: extroot: not configured
[    6.531369] UBIFS (ubi0:1): un-mount UBI device 0
[    6.536097] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops
[    6.544028] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 809
[    6.591527] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[    6.599392] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    6.609356] UBIFS (ubi0:1): FS size: 61329408 bytes (58 MiB, 483 LEBs), journal size 3047424 bytes (2 MiB, 24 LEBs)
[    6.619838] UBIFS (ubi0:1): reserved for root: 2896739 bytes (2828 KiB)
[    6.626483] UBIFS (ubi0:1): media format: w4/r0 (latest is w4/r0), UUID DEE50754-EFFE-4990-A7A6-C97266C9BEF0, small LPT model
[    6.641627] mount_root: loading kmods from internal overlay
[    6.652909] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[    6.670201] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[    7.078279] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[    7.086484] block: extroot: not configured
[    7.132013] mount_root: switching to ubifs overlay
[    7.176201] ubi1: attaching mtd9
[    7.407547] ubi1: scanning is finished
[    7.415742] ubi1: attached mtd9 (name "syscfg", size 86 MiB)
[    7.421435] ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    7.428338] ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    7.435155] ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
[    7.442148] ubi1: good PEBs: 680, bad PEBs: 8, corrupted PEBs: 0
[    7.448177] ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
[    7.455430] ubi1: max/mean erase counter: 6/4, WL threshold: 4096, image sequence number: 1148089792
[    7.464603] ubi1: available PEBs: 0, total reserved PEBs: 680, PEBs reserved for bad PEB handling: 32
[    7.473869] ubi1: background thread "ubi_bgt1d" started, PID 824
[    7.485213] UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 828
[    7.537764] UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "syscfg"
[    7.545202] UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    7.555161] UBIFS (ubi1:0): FS size: 80375808 bytes (76 MiB, 633 LEBs), journal size 4063232 bytes (3 MiB, 32 LEBs)
[    7.565642] UBIFS (ubi1:0): reserved for root: 3796347 bytes (3707 KiB)
[    7.572287] UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID A5EAB2F8-92D3-4D0B-A69A-9F6CA9A608B3, small LPT model
[    7.585463] urandom-seed: Seeding with /etc/urandom.seed
[    7.684142] procd: - early -
[    7.687055] procd: - watchdog -
[    8.315049] procd: - ubus -
[    8.371904] procd: - init -
[    8.546612] kmodloader: loading kernel modules from /etc/modules.d/*
[    8.557859] tun: Universal TUN/TAP device driver, 1.6
[    8.562965] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    8.571391] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[    8.580401] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    8.587876] cryptodev: driver 1.8 loaded.
[    8.592340] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
[    8.600387] Backport generated by backports.git backports-20160324-13-g24da7d3c
[    8.615059] <<Marvell 802.11ac Wireless Network Driver version 10.3.2.0-20170110>>
[    8.622702] pci 0000:00:01.0: enabling device (0140 -> 0142)
[    8.628443] ieee80211 phy0: priv->iobase0 = e0f80000
[    8.628454] ieee80211 phy0: priv->iobase1 = e1200000
[    8.628463] ieee80211 phy0: priv->pcmd_buf = ddf08000  priv->pphys_cmd_buf = 1df08000
[    8.636458] ieee80211 phy0: fw download start
[    8.699990] ieee80211 phy0: FwSize = 207660 downloaded Size = 207660 curr_iteration 65522
[   12.431324] ieee80211 phy0: fw download complete
[   12.431783] ieee80211 phy0: pcmd = ddf08000
[   12.449817] ieee80211 phy0: firmware version: 0x7080004
[   12.809338] ieee80211 phy0: firmware region code: 10
[   12.851995] ieee80211 phy0: 2G disabled, 5G enabled
[   12.856895] ieee80211 phy0: 4 TX antennas, 4 RX antennas
[   12.862298] pci 0000:00:02.0: enabling device (0140 -> 0142)
[   12.868032] ieee80211 phy1: priv->iobase0 = e1380000
[   12.868043] ieee80211 phy1: priv->iobase1 = e1600000
[   12.868052] ieee80211 phy1: priv->pcmd_buf = dddf0000  priv->pphys_cmd_buf = 1ddf0000
[   12.874418] ieee80211 phy1: fw download start
[   12.939175] ieee80211 phy1: FwSize = 207660 downloaded Size = 207660 curr_iteration 65527
[   14.327325] ieee80211 phy1: fw download complete
[   14.327812] ieee80211 phy1: pcmd = dddf0000
[   14.345344] ieee80211 phy1: firmware version: 0x7080004
[   14.706323] ieee80211 phy1: firmware region code: 10
[   14.750021] ieee80211 phy1: 2G enabled, 5G disabled
[   14.754934] ieee80211 phy1: 4 TX antennas, 4 RX antennas
[   14.762803] u32 classifier
[   14.765522]     input device check on
[   14.769196]     Actions configured
[   14.773037] Mirror/redirect action on
[   14.778285] nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
[   14.790080] ip_tables: (C) 2000-2006 Netfilter Core Team
[   14.799009] mwifiex: rx work enabled, cpus 2
[   14.846998] usbcore: registered new interface driver ums-alauda
[   14.853672] usbcore: registered new interface driver ums-cypress
[   14.860218] usbcore: registered new interface driver ums-datafab
[   14.866723] usbcore: registered new interface driver ums-freecom
[   14.873187] usbcore: registered new interface driver ums-isd200
[   14.879542] usbcore: registered new interface driver ums-jumpshot
[   14.886112] usbcore: registered new interface driver ums-karma
[   14.892282] usbcore: registered new interface driver ums-sddr09
[   14.898499] usbcore: registered new interface driver ums-sddr55
[   14.904752] usbcore: registered new interface driver ums-usbat
[   14.917781] xt_time: kernel timezone is -0000
[   14.925132] PPP generic driver version 2.4.2
[   14.929843] NET: Registered protocol family 24
[   14.935112] kmodloader: done loading kernel modules from /etc/modules.d/*
[   15.469997] mwifiex_sdio mmc0:0001:1: info: FW download over, size 391772 bytes
[   15.831665] mwifiex_sdio mmc0:0001:1: WLAN FW is active
[   15.864262] mwifiex_sdio mmc0:0001:1: CMD_RESP: cmd 0x242 error, result=0x2
[   15.871261] mwifiex_sdio mmc0:0001:1: mwifiex_process_cmdresp: cmd 0x242 failed during       initialization
[   15.890625] mwifiex_sdio mmc0:0001:1: info: MWIFIEX VERSION: mwifiex 1.0 (15.68.7.p5)
[   15.898674] mwifiex_sdio mmc0:0001:1: driver_version = mwifiex 1.0 (15.68.7.p5)
[   16.052347] mvneta f1034000.ethernet eth0: configuring for fixed link mode
[   16.059309] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   16.065375] mvneta f1034000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[   16.073372] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   16.081683] br-lan: port 1(eth0.1) entered blocking state
[   16.087106] br-lan: port 1(eth0.1) entered disabled state
[   16.092675] device eth0.1 entered promiscuous mode
[   16.097485] device eth0 entered promiscuous mode
[   16.103227] br-lan: port 1(eth0.1) entered blocking state
[   16.108650] br-lan: port 1(eth0.1) entered forwarding state
[   16.122758] mvneta f1070000.ethernet eth1: configuring for fixed link mode
[   16.130044] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   16.136169] mvneta f1070000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[   16.144170] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   16.342477] pppoe-wan: renamed from ppp0
[   16.900336] ieee80211 phy1: change: 0xffffffff
[   17.006509] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[   17.137396] ieee80211 phy0: change: 0xffffffff
[   17.271596] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   17.277594] br-lan: port 2(wlan1) entered blocking state
[   17.282955] br-lan: port 2(wlan1) entered disabled state
[   17.288408] device wlan1 entered promiscuous mode
[   17.293166] br-lan: port 2(wlan1) entered blocking state
[   17.298502] br-lan: port 2(wlan1) entered forwarding state
[   17.304255] br-lan: port 2(wlan1) entered disabled state
[   17.309734] br-lan: port 3(wlan0) entered blocking state
[   17.315091] br-lan: port 3(wlan0) entered disabled state
[   17.320543] device wlan0 entered promiscuous mode
[   17.327109] ieee80211 phy0: change: 0x100
[   17.344423] ieee80211 phy0: change: 0x40
[   17.380440] ieee80211 phy1: change: 0x100
[   17.392530] ieee80211 phy1: change: 0x42
[   17.593821] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[   17.600257] br-lan: port 2(wlan1) entered blocking state
[   17.605603] br-lan: port 2(wlan1) entered forwarding state
[   17.611269] ieee80211 phy0: change: 0x40
[   17.671185] ieee80211 phy1: change: 0x20
[   17.861365] ieee80211 phy0: change: 0x40
[   17.993370] ieee80211 phy0: change: 0x100
[   18.060535] ieee80211 phy0: change: 0x100
[   18.073629] ieee80211 phy0: change: 0x42
[   18.341340] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   18.347812] br-lan: port 3(wlan0) entered blocking state
[   18.353170] br-lan: port 3(wlan0) entered forwarding state
 root@LEDE:~# lsusb
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 04e8:1f05 Samsung Electronics Co., Ltd S2 Portable [JMicron] (500GB)
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub

After i remove the cable and hotplug i get this additional lines in DMESG:

 #
[  527.103849] usb 3-1: new SuperSpeed USB device number 2 using xhci-hcd
[  527.134880] usb-storage 3-1:1.0: USB Mass Storage device detected
[  527.141155] scsi host3: usb-storage 3-1:1.0
[  528.154087] scsi 3:0:0:0: Direct-Access     Seagate  Expansion        1805 PQ: 0 ANSI: 6
[  529.455313] sd 3:0:0:0: [sdb] 1953525167 512-byte logical blocks: (1.00 TB/932 GiB)
[  529.463210] sd 3:0:0:0: [sdb] Write Protect is off
[  529.468032] sd 3:0:0:0: [sdb] Mode Sense: 33 00 00 08
[  529.473381] sd 3:0:0:0: [sdb] No Caching mode page found
[  529.478724] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[  529.499962]  sdb: sdb1 sdb2
[  529.503903] sd 3:0:0:0: [sdb] Attached SCSI disk
[  612.132851] EXT4-fs (sdb2): mounted filesystem with ordered data mode. Opts:
root@LEDE:~# lsusb
Bus 003 Device 002: ID 0bc2:231b Seagate RSS LLC
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 04e8:1f05 Samsung Electronics Co., Ltd S2 Portable [JMicron] (500GB)
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub 


27.02.2017564Base systemBug ReportVery LowLowWRT1900ACV1 Mamba No crashlog createdTrunkUnconfirmed Task Description

WRT1900ACV1 4.9.13
LEDE Reboot SNAPSHOT r3607+2-d49ddcd / LuCI Master (git-17.058.53452-829344d)
The +2 above is due to blogic’s blockd trial. (so far fine)
This has been showing up in system log since I have been on 4.9.

Mon Feb 27 10:00:03 2017 kern.warn kernel: [ 0.064607] Crashlog allocated RAM at address 0x3f00000
Mon Feb 27 10:00:03 2017 kern.err kernel: [ 1.276797] cpu cpu1: opp_list_debug_create_link: Failed to create link
Mon Feb 27 10:00:03 2017 kern.err kernel: [ 1.283441] cpu cpu1: _add_opp_dev: Failed to register opp debugfs (-12)

Crash/reboot is very rare. There is nothing showing in the external log all normal then reboot.

 


13.10.2016224Base systemBug ReportVery LowLowwrong source IP when logging to remote IPv6 syslog serv...TrunkAssigned Task Description

Hello,

I’m trying to send log to remote IPv6 syslog server (x:y:z:12::1), but packets received by syslog server are invalid. Instead of public IPv6 address, syslog udp packets are sent with ::1 source IP and therefore ignored by destination server. Logging over IPv4 works ok.

tcpdump log from destination syslog server:
23:34:16.988433 IP6 ::1.38044 > x:y:z:12::1.514: SYSLOG daemon.notice, length: 65

Configuration:

/etc/config/system:

 option log_ip 'x:y:z:12::1'

Device is in the same range as syslog server (x:y:z:12::119/64) and has native IPv6 connectivity. Other services (dropbear, ntp client, snmpd, luci) are running fine over IPv6.

Device is TP-Link WDR3600, running lede reboot-1818-gb81fc29.

18.06.2017855Base systemBug ReportVery LowMediumWrong MAC address (00:00:00:00:00:01) on Arcadyan AR751...lede-17.01Unconfirmed Task Description
root@LEDE:~# ifconfig | grep HW
br-lan    Link encap:Ethernet  HWaddr 00:00:00:00:00:01  
eth0      Link encap:Ethernet  HWaddr 00:00:00:00:00:01  
eth0.1    Link encap:Ethernet  HWaddr 00:00:00:00:00:01  
eth0.2    Link encap:Ethernet  HWaddr 00:00:00:00:00:01  
wlan0     Link encap:Ethernet  HWaddr 00:00:00:00:00:02

I know MAC addresses can be overriden in config, but is it possible to automatically detect the original addresses?

13.03.2017624PackagesBug ReportVery LowLowWrong default WAN interface on SQM & BCP38 packageslede-17.01Unconfirmed Task Description

Supply the following if possible:
- Device problem occurs on: Archer C7v2
- Software versions of LEDE release, packages, etc.: 17.01 final
- Steps to reproduce: just install default packages

By default, SQM and BCP38 packages configure rules on eth1, but on C7 this is LAN interface and not WAN. Both must be changed to apply default configuration to eth0.
This behaviour cames from OpenWRT.

 


28.12.2016362Base systemBug ReportVery LowMediumWR1043ND v4 Slow WAN -> LAN Whilst Synced @100MbpsTrunkWaiting on reporter Task Description

Recently, builds for this device have started to be made, but there’s a very peculiar issue I’ve found. Any client that is synced to 100 Mbps (and not 1 Gbps, in my case due to incapacity of the cable used) gets their speed seemingly throttled to 20-30 Mbps. My connection is a 100 Mbps connection, and I get full 95 Mbps (Hardware NAT disabled) on the stock firmware, and I also get this speed on LEDE only if I use a 1 Gbps link.

Speedtest on the stock firmware with the 100 Mbps link: http://www.speedtest.net/result/5904234776.png Speedtest on the latest LEDE with the 100 Mbps link: http://www.speedtest.net/result/5915271748.png 1 Gbps links get full speed, as expected.

If I perform a transfer from LAN to LAN, I get full speed on the 100 Mbps link. The resulting speed graph is not a hard-cap, but seemingly some kind of throttle/flow control being applied. I cannot change any settings with ethtool as it throws ‘not supported’ errors.

Only happens WAN > LAN connections.
Nothing of interest in the logs, unless I can somehow get a more verbose log of the connection status.

11.11.20171162Base systemBug ReportVery LowLowwpa_supplicant dead loop in fuction wpas_ctrl_msg_queue...TrunkUnconfirmed Task Description

lede-17.01
https://github.com/lede-project/source.git 4c3953ba291abfb1d28b1452b6e519367bf4f242

db120

I am test ath9k Stability. And after 1 day. wpa_supplicant MSG_DUMP loop:

daemon.debug wpa_supplicant[9844]: CTRL: Had to throttle pending event message transmission for (sock 18 gsock -1)

I have two clients device connect ap. Both two clients all report this log. But ap have no any info. And restart wpa_supplicant with wifi. Log is missing.

17.06.2017851KernelBug ReportVery LowLowWNR2200 USB Port don't functioned andin the Bugfixed D...AllUnconfirmed Task Description

The USB Port don’t became the right power from the right GPIO.

- Netgear WNR2200
- LEDE 17.01.2 (stable, unstable, trunk)
- Flash an image with the unmodified driver target/linux/ar71xx/files/arch/mips/ath79/mach-wnr2000.c

Hello,

it’s an known and partially solved bug in OpenWRT but not solved in the LEDE sources. Now the sources from OpenWRT source solve the problem with the Power but some leds (wlan especially) don’t functioned and the original from LEDE source trigger the right GPIOs for the LEDs and this functioned well, but the usb port don’t became power and extroot don’t functioned.

Now i have used this source from http://git.openwrt.org/?p=openwrt.git;a=commit;h=95f36ebcd774a8e93ad2a1331f45d1a9da4fe8ff and recompiled LEDE from scratch and how i wrote wlan-led as an example don’t functioned but the usb port became power and block info make the usb stick viewable.

Thx.

06.04.2017682Base systemBug ReportVery LowLowWNR2000v3 bootloop after installing 17.01.0lede-17.01Unconfirmed Task Description

My Netgear WNR2000v3 goes into a bootloop after installing 17.01.0 but is fine with the Trunk snapshot from 6 April 2017.
When it starts up, it gives me 4 pings, then it stops responding until it wakes back up. When it stops responding,m the network interface acts like it is disconnected (no link), then it comes back up just before it responds to pings again.
I had time tonight to plug a serial console into it and record what it does when you install 17.01.0
These were installed with TFTP from the recovery (hold reset for ~30 seconds when powering up, then tftp the image to 192.168.1.1)
Attached are two bootlogs:

  1. Bootlog of the upgrade to 17.01 from recovery mode using the lede-17.01.0-r3205-59508e3-ar71xx-generic-wnr2000v3-squashfs-factory-NA.img image (goes into a bootloop after the install): WNR2000V3To17.01UpgradeBootlog.txt
  2. Bootlog of the upgrade to the 6 April 2017 nightly (r3922-9613d97) using the lede-ar71xx-generic-wnr2000v3-squashfs-factory-NA.img image (works as expected): WNR2000V3To6April17SnapshotUpgradeBootlog.txt

I saw the same thing installing lede-17.01.0-r3205-59508e3-ar71xx-generic-wnr2000v3-squashfs-factory-NA.img from the factory web interface (Netgear wnr2000v3-V1.1.2.14) but I didnt save a bootlog of that

Let me know if more info is needed.

Aaron Z


06.07.2017890Base systemBug ReportVery LowLowWNDR3400v1 brcmsmac fails to attach phy0 & phy1, error ...TrunkUnconfirmed Task Description

On my Netgear WNDR3400v1, WiFi doesn’t work with the brcmsmac driver, it should.

Here is the error in dmesg upon loading the brcmsmac driver:

[   13.922244] brcmsmac bcma0:1: mfg 4bf core 812 rev 17 class 0 irq 3
[   13.928938] ieee80211 phy0: wl0: brcms_b_attach: Unsupported Broadcom board type (0xb4cf) or revision level (0x0)
[   13.939483] ieee80211 phy0: wl0: brcms_b_attach: failed with err 15
[   13.945869] ieee80211 phy0: wl0: brcms_c_attach: failed with err 15
[   13.952317] ieee80211 phy0: brcmsmac: attach() failed with code 15
[   13.958605] brcmsmac: brcms_bcma_probe: brcms_attach failed!
[   13.964536] brcmsmac bcma1:1: mfg 4bf core 812 rev 23 class 0 irq 6
[   13.971222] bcma: bus1: Switched to core: 0x812
[   13.971613] ieee80211 phy1: wl0: brcms_b_attach: Unsupported Broadcom board type (0xb4cf) or revision level (0x0)
[   13.982136] ieee80211 phy1: wl0: brcms_b_attach: failed with err 15
[   13.988517] ieee80211 phy1: wl0: brcms_c_attach: failed with err 15
[   13.994965] ieee80211 phy1: brcmsmac: attach() failed with code 15
[   14.001311] brcmsmac: brcms_bcma_probe: brcms_attach failed!

It seems it is reading the revision level incorrectly, and refusing to load.

nvram show displays:

boardnum=01
boardtype=0xb4cf
boardrev=0x1100

System Information:

Reboot (SNAPSHOT, r4529-05d6e92)

root@lede:~# cat /etc/openwrt_release 
DISTRIB_ID='LEDE'
DISTRIB_RELEASE='SNAPSHOT'
DISTRIB_REVISION='r4529-05d6e92'
DISTRIB_CODENAME='reboot'
DISTRIB_TARGET='brcm47xx/mips74k'
DISTRIB_ARCH='mipsel_74kc'
DISTRIB_DESCRIPTION='LEDE Reboot SNAPSHOT r4529-05d6e92'
DISTRIB_TAINTS='no-all'

root@lede:~# uname -a
Linux lede 4.4.74 #0 Sun Jul 2 21:10:06 2017 mips GNU/Linux

   
[ logread ]
Wed Jul  5 22:22:41 2017 kern.notice kernel: [    0.000000] Linux version 4.4.74 (buildbot@builds) (gcc version 5.4.0 (LEDE GCC 5.4.0 r4456-d98cafc) ) #0 Sun Jul 2 21:10:06 2017
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000] CPU0 revision is: 00019740 (MIPS 74Kc)
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000] bcm47xx: Using bcma bus
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000] bcma: bus0: Found chip with id 0x4716, rev 0x01 and package 0x0A
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000] Determined physical RAM map:
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000]  memory: 04000000 @ 00000000 (usable)
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000] Initrd not found or empty - disabling initrd
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000] Zone ranges:
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000]   HighMem  empty
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000] Movable zone start for each node
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000] Early memory node ranges
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.000000] On node 0 totalpages: 16384
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.000000] free_area_init_node: node 0, pgdat 803a64c0, node_mem_map 81000000
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.000000]   Normal zone: 128 pages used for memmap
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.000000]   Normal zone: 0 pages reserved
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.000000]   Normal zone: 16384 pages, LIFO batch:3
Wed Jul  5 22:22:41 2017 kern.warn kernel: [    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Wed Jul  5 22:22:41 2017 kern.warn kernel: [    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.000000] pcpu-alloc: [0] 0 
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Wed Jul  5 22:22:41 2017 kern.notice kernel: [    0.000000] Kernel command line:  noinitrd console=ttyS0,115200
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000] Writing ErrCtl register=00000000
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000] Readback ErrCtl register=00000000
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000] Memory: 60556K/65536K available (3002K kernel code, 134K rwdata, 696K rodata, 188K init, 294K bss, 4980K reserved, 0K cma-reserved, 0K highmem)
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000] NR_IRQS:128
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x1F, class 0x0)
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x11, class 0x0)
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000] bcma: bus0: Core 2 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x00, class 0x0)
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000] bcma: bus0: Core 3 found: MIPS 74K (manuf 0x4A7, id 0x82C, rev 0x01, class 0x0)
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000] bcma: bus0: Core 4 found: USB 2.0 Host (manuf 0x4BF, id 0x819, rev 0x04, class 0x0)
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000] bcma: bus0: Core 5 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0E, class 0x0)
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000] bcma: bus0: Core 6 found: DDR1/DDR2 Memory Controller (manuf 0x4BF, id 0x82E, rev 0x01, class 0x0)
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000] bcma: bus0: Core 7 found: Internal Memory (manuf 0x4BF, id 0x80E, rev 0x07, class 0x0)
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000] bcma: bus0: Core 8 found: I2S (manuf 0x4BF, id 0x834, rev 0x00, class 0x0)
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.000000] bcma: bus0: Found rev 5 PMU (capabilities 0x11242C05)
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.000000] bcma: bus0: Found serial flash
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000] bcma: bus0: Found M25P64 serial flash (size: 8192KiB, blocksize: 0x10000, blocks: 128)
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000] bcma: bus0: Early bus registered
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000] MIPS: machine is Unknown Board
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000] bcm47xx: Setting up vectored interrupts
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 8438235966 ns
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000015] sched_clock: 32 bits at 226MHz, resolution 4ns, wraps every 9481163773ns
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.000088] Calibrating delay loop... 226.09 BogoMIPS (lpj=1130496)
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.070063] pid_max: default: 32768 minimum: 301
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.070318] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.070345] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.074642] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.074715] futex hash table entries: 256 (order: -1, 3072 bytes)
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.076193] NET: Registered protocol family 16
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.099321] clocksource: Switched to clocksource MIPS
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.101966] NET: Registered protocol family 2
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.103621] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.103678] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.103719] TCP: Hash tables configured (established 1024 bind 1024)
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.103896] UDP hash table entries: 256 (order: 0, 4096 bytes)
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.103944] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.104461] NET: Registered protocol family 1
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.104612] PCI: CLS 0 bytes, default 32
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.113504] bcma: bus0: Using SPROM revision 0 provided by platform.
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.113545] bcma: bus0: PMU resource config unknown or not needed for device 0x4716
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.115561] bcma: bus0: Workarounds unknown or not needed for device 0x4716
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.115580] bcma: bus0: Initializing MIPS core...
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.115601] bcma: bus0: Moved i2s interrupt to oob line 7 instead of 8
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.115628] bcma: bus0: set_irq: core 0x0812, irq 3 => 3
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.115651] bcma: bus0: set_irq: core 0x082d, irq 4 => 4
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.115674] bcma: bus0: set_irq: core 0x0819, irq 5 => 5
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.115697] bcma: bus0: set_irq: core 0x0820, irq 6 => 6
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.115718] bcma: bus0: set_irq: core 0x0800, irq 2 => 2
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.115741] bcma: bus0: set_irq: core 0x0834, irq 0 => 2
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.115756] bcma: bus0: IRQ reconfiguration done
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.115772] bcma: core 0x0800, irq : 2(S)* 3  4  5  6  D  I 
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.115825] bcma: core 0x0812, irq : 2(S)  3* 4  5  6  D  I 
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.115869] bcma: core 0x082d, irq : 2(S)  3  4* 5  6  D  I 
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.115913] bcma: core 0x082c, irq : 2(S)  3  4  5  6  D  I*
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.115957] bcma: core 0x0819, irq : 2(S)  3  4  5* 6  D  I 
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.116001] bcma: core 0x0820, irq : 2(S)  3  4  5  6* D  I 
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.116045] bcma: core 0x082e, irq : 2(S)  3  4  5  6  D* I 
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.116088] bcma: core 0x080e, irq : 2(S)  3  4  5  6  D  I*
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.116130] bcma: core 0x0834, irq : 2(S)* 3  4  5  6  D  I 
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.116176] bcma: bus0: PCIEcore in host mode found
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.304669] PCI host bridge to bus 0000:00
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.304727] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0bffffff]
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.304756] pci_bus 0000:00: root bus resource [io  0x0100-0x07ff]
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.304785] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.304814] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.304903] pci 0000:00:00.0: [14e4:4716] type 00 class 0x060000
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.304948] bcma: PCI: Fixing up bridge 0000:00:00.0
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.304969] bcma: PCI: Fixing up device 0000:00:00.0
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.305033] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit]
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.305073] pci 0000:00:00.0: reg 0x18: [mem 0x00000000-0x07ffffff 64bit]
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.305187] pci 0000:00:00.0: supports D1 D2
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.305595] pci 0000:00:00.1: [14e4:0000] type 00 class 0x060000
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.305645] bcma: PCI: Fixing up bridge 0000:00:00.1
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.305666] bcma: PCI: Fixing up device 0000:00:00.1
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.305731] pci 0000:00:00.1: reg 0x10: [mem 0x00000000-0x00003fff 64bit]
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.305770] pci 0000:00:00.1: reg 0x18: [mem 0x00000000-0x07ffffff 64bit]
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.305878] pci 0000:00:00.1: supports D1 D2
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.306355] pci 0000:00:01.0: [14e4:a8d8] type 00 class 0x028000
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.306490] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit]
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.306593] bcma: PCI: Fixing up addresses 0000:00:01.0
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.306642] pci 0000:00:01.0: BAR 0: assigned [mem 0x08000000-0x08003fff 64bit]
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.306809] pci 0000:00:01.0: supports D1 D2
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    0.307254] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.308856] bcma: bus0: Bus registered
Wed Jul  5 22:22:41 2017 kern.warn kernel: [    0.310393] Crashlog allocated RAM at address 0x3f00000
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.344150] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.344205] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.349655] io scheduler noop registered
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.349707] io scheduler deadline registered (default)
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.350248] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.355394] console [ttyS0] disabled
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.375653] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 2, base_baud = 1250000) is a U6_16550A
Wed Jul  5 22:22:41 2017 kern.info kernel: [    0.872455] console [ttyS0] enabled
Wed Jul  5 22:22:41 2017 kern.notice kernel: [    0.989922] 7 bcm47xxpart partitions found on MTD device bcm47xxsflash
Wed Jul  5 22:22:41 2017 kern.notice kernel: [    0.996576] Creating 7 MTD partitions on "bcm47xxsflash":
Wed Jul  5 22:22:41 2017 kern.notice kernel: [    1.002140] 0x000000000000-0x000000040000 : "boot"
Wed Jul  5 22:22:41 2017 kern.notice kernel: [    1.011599] 0x000000040000-0x0000007e0000 : "firmware"
Wed Jul  5 22:22:41 2017 kern.notice kernel: [    1.020126] 0x0000007e0000-0x0000007f0000 : "board_data"
Wed Jul  5 22:22:41 2017 kern.notice kernel: [    1.028709] 0x0000007f0000-0x000000800000 : "nvram"
Wed Jul  5 22:22:41 2017 kern.notice kernel: [    1.036956] 0x00000004001c-0x000000040920 : "loader"
Wed Jul  5 22:22:41 2017 kern.notice kernel: [    1.045355] 0x000000040920-0x00000017dc00 : "linux"
Wed Jul  5 22:22:41 2017 kern.notice kernel: [    1.053621] 0x00000017dc00-0x0000007e0000 : "rootfs"
Wed Jul  5 22:22:41 2017 kern.notice kernel: [    1.061906] mtd: device 6 (rootfs) set to be root filesystem
Wed Jul  5 22:22:41 2017 kern.notice kernel: [    1.067729] 1 squashfs-split partitions found on MTD device rootfs
Wed Jul  5 22:22:41 2017 kern.notice kernel: [    1.074136] 0x000000360000-0x0000007e0000 : "rootfs_data"
Wed Jul  5 22:22:41 2017 kern.info kernel: [    1.086521] libphy: Fixed MDIO Bus: probed
Wed Jul  5 22:22:41 2017 kern.info kernel: [    1.091101] bgmac_bcma bcma0:2: Found PHY addr: 30 (NOREGS)
Wed Jul  5 22:22:41 2017 kern.info kernel: [    1.100515] libphy: bcma_mdio mii bus: probed
Wed Jul  5 22:22:41 2017 kern.warn kernel: [    1.104979] bgmac_bcma bcma0:2: Support for Roboswitch not implemented
Wed Jul  5 22:22:41 2017 kern.info kernel: [    1.264041] b53_common: found switch: BCM5325, rev 0
Wed Jul  5 22:22:41 2017 kern.info kernel: [    1.270621] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded
Wed Jul  5 22:22:41 2017 kern.info kernel: [    1.276982] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds)
Wed Jul  5 22:22:41 2017 kern.warn kernel: [    1.285141] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
Wed Jul  5 22:22:41 2017 kern.info kernel: [    1.291021] bcma: PCI: Fixing up device 0000:00:01.0
Wed Jul  5 22:22:41 2017 kern.info kernel: [    1.296150] bcma: bus1: Found chip with id 43224, rev 0x01 and package 0x08
Wed Jul  5 22:22:41 2017 kern.info kernel: [    1.303351] bcma: bus1: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x22, class 0x0)
Wed Jul  5 22:22:41 2017 kern.info kernel: [    1.312133] bcma: bus1: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x17, class 0x0)
Wed Jul  5 22:22:41 2017 kern.info kernel: [    1.321015] bcma: bus1: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0F, class 0x0)
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    1.329246] bcma: bus1: Found rev 6 PMU (capabilities 0x108C2606)
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    1.330088] bcma: bus1: Using SPROM revision 0 provided by platform.
Wed Jul  5 22:22:41 2017 kern.debug kernel: [    1.330132] bcma: bus1: PMU resource config unknown or not needed for device 0xA8D8
Wed Jul  5 22:22:41 2017 kern.info kernel: [    1.340850] bcma: bus1: Bus registered
Wed Jul  5 22:22:41 2017 kern.info kernel: [    1.346903] NET: Registered protocol family 10
Wed Jul  5 22:22:41 2017 kern.info kernel: [    1.357396] NET: Registered protocol family 17
Wed Jul  5 22:22:41 2017 kern.info kernel: [    1.362216] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
Wed Jul  5 22:22:41 2017 kern.info kernel: [    1.375148] 8021q: 802.1Q VLAN Support v1.8
Wed Jul  5 22:22:41 2017 kern.info kernel: [    1.393155] VFS: Mounted root (squashfs filesystem) readonly on device 31:6.
Wed Jul  5 22:22:41 2017 kern.info kernel: [    1.401759] Freeing unused kernel memory: 188K (803c1000 - 803f0000)
Wed Jul  5 22:22:41 2017 user.info kernel: [    3.050931] init: Console is alive
Wed Jul  5 22:22:41 2017 user.info kernel: [    3.054861] init: - watchdog -
Wed Jul  5 22:22:41 2017 user.info kernel: [    4.254646] kmodloader: loading kernel modules from /etc/modules-boot.d/*
Wed Jul  5 22:22:41 2017 kern.info kernel: [    4.402007] usbcore: registered new interface driver usbfs
Wed Jul  5 22:22:41 2017 kern.info kernel: [    4.407764] usbcore: registered new interface driver hub
Wed Jul  5 22:22:41 2017 kern.info kernel: [    4.413517] usbcore: registered new device driver usb
Wed Jul  5 22:22:41 2017 kern.info kernel: [    4.427524] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Wed Jul  5 22:22:41 2017 kern.info kernel: [    4.437246] ehci-platform: EHCI generic platform driver
Wed Jul  5 22:22:41 2017 kern.info kernel: [    4.442860] ehci-platform ehci-platform.0: EHCI Host Controller
Wed Jul  5 22:22:41 2017 kern.info kernel: [    4.449006] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
Wed Jul  5 22:22:41 2017 kern.info kernel: [    4.457485] ehci-platform ehci-platform.0: irq 5, io mem 0x18004000
Wed Jul  5 22:22:41 2017 kern.info kernel: [    4.479401] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
Wed Jul  5 22:22:41 2017 kern.info kernel: [    4.487835] hub 1-0:1.0: USB hub found
Wed Jul  5 22:22:41 2017 kern.info kernel: [    4.492481] hub 1-0:1.0: 2 ports detected
Wed Jul  5 22:22:41 2017 kern.info kernel: [    4.502125] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Wed Jul  5 22:22:41 2017 kern.info kernel: [    4.510967] ohci-platform: OHCI generic platform driver
Wed Jul  5 22:22:41 2017 kern.info kernel: [    4.516448] ohci-platform ohci-platform.0: Generic Platform OHCI controller
Wed Jul  5 22:22:41 2017 kern.info kernel: [    4.523735] ohci-platform ohci-platform.0: new USB bus registered, assigned bus number 2
Wed Jul  5 22:22:41 2017 kern.info kernel: [    4.532182] ohci-platform ohci-platform.0: irq 5, io mem 0x18009000
Wed Jul  5 22:22:41 2017 kern.info kernel: [    4.595330] hub 2-0:1.0: USB hub found
Wed Jul  5 22:22:41 2017 kern.info kernel: [    4.600124] hub 2-0:1.0: 2 ports detected
Wed Jul  5 22:22:41 2017 user.info kernel: [    4.608697] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
Wed Jul  5 22:22:41 2017 user.info kernel: [    4.626861] init: - preinit -
Wed Jul  5 22:22:41 2017 kern.info kernel: [    5.011347] usb 1-1: new high-speed USB device number 2 using ehci-platform
Wed Jul  5 22:22:41 2017 kern.notice kernel: [    5.263503] random: procd: uninitialized urandom read (4 bytes read, 9 bits of entropy available)
Wed Jul  5 22:22:41 2017 kern.notice kernel: [    6.414938] random: jshn: uninitialized urandom read (4 bytes read, 11 bits of entropy available)
Wed Jul  5 22:22:41 2017 kern.notice kernel: [    6.608349] random: jshn: uninitialized urandom read (4 bytes read, 11 bits of entropy available)
Wed Jul  5 22:22:41 2017 kern.notice kernel: [    6.731613] random: jshn: uninitialized urandom read (4 bytes read, 11 bits of entropy available)
Wed Jul  5 22:22:41 2017 kern.info kernel: [    7.012119] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Wed Jul  5 22:22:41 2017 kern.info kernel: [    7.018248] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
Wed Jul  5 22:22:41 2017 kern.info kernel: [    8.569470] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Wed Jul  5 22:22:41 2017 kern.info kernel: [    8.576495] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
Wed Jul  5 22:22:41 2017 kern.notice kernel: [   10.681655] jffs2: notice: (375) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
Wed Jul  5 22:22:41 2017 user.info kernel: [   10.705445] mount_root: switching to jffs2 overlay
Wed Jul  5 22:22:41 2017 user.warn kernel: [   10.759409] urandom-seed: Seeding with /etc/urandom.seed
Wed Jul  5 22:22:41 2017 user.info kernel: [   10.971431] procd: - early -
Wed Jul  5 22:22:41 2017 user.info kernel: [   10.974613] procd: - watchdog -
Wed Jul  5 22:22:41 2017 user.info kernel: [   11.730144] procd: - watchdog -
Wed Jul  5 22:22:41 2017 user.info kernel: [   11.734119] procd: - ubus -
Wed Jul  5 22:22:41 2017 kern.notice kernel: [   11.756070] random: ubusd: uninitialized urandom read (4 bytes read, 20 bits of entropy available)
Wed Jul  5 22:22:41 2017 kern.notice kernel: [   11.789743] random: ubusd: uninitialized urandom read (4 bytes read, 20 bits of entropy available)
Wed Jul  5 22:22:41 2017 kern.notice kernel: [   11.799846] random: ubusd: uninitialized urandom read (4 bytes read, 20 bits of entropy available)
Wed Jul  5 22:22:41 2017 kern.notice kernel: [   11.809088] random: ubusd: uninitialized urandom read (4 bytes read, 20 bits of entropy available)
Wed Jul  5 22:22:41 2017 kern.notice kernel: [   11.819720] random: ubusd: uninitialized urandom read (4 bytes read, 20 bits of entropy available)
Wed Jul  5 22:22:41 2017 kern.notice kernel: [   11.828937] random: ubusd: uninitialized urandom read (4 bytes read, 20 bits of entropy available)
Wed Jul  5 22:22:41 2017 user.info kernel: [   11.840154] procd: - init -
Wed Jul  5 22:22:41 2017 user.info kernel: [   13.039395] kmodloader: loading kernel modules from /etc/modules.d/*
Wed Jul  5 22:22:41 2017 kern.info kernel: [   13.065020] tun: Universal TUN/TAP device driver, 1.6
Wed Jul  5 22:22:41 2017 kern.info kernel: [   13.070278] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
Wed Jul  5 22:22:41 2017 kern.info kernel: [   13.085691] ip6_tables: (C) 2000-2006 Netfilter Core Team
Wed Jul  5 22:22:41 2017 kern.info kernel: [   13.145711] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
Wed Jul  5 22:22:41 2017 kern.info kernel: [   13.153955] Backport generated by backports.git backports-20160324-13-g24da7d3c
Wed Jul  5 22:22:41 2017 kern.info kernel: [   13.171588] ip_tables: (C) 2000-2006 Netfilter Core Team
Wed Jul  5 22:22:41 2017 kern.info kernel: [   13.193691] nf_conntrack version 0.5.0 (949 buckets, 3796 max)
Wed Jul  5 22:22:41 2017 kern.info kernel: [   13.317055] xt_time: kernel timezone is -0000
Wed Jul  5 22:22:41 2017 kern.info kernel: [   13.325369] usbcore: registered new interface driver cdc_ether
Wed Jul  5 22:22:41 2017 kern.info kernel: [   13.427171] PPP generic driver version 2.4.2
Wed Jul  5 22:22:41 2017 kern.info kernel: [   13.436494] NET: Registered protocol family 24
Wed Jul  5 22:22:41 2017 kern.info kernel: [   13.450675] rndis_host 1-1:1.0 usb0: register 'rndis_host' at usb-ehci-platform.0-1, RNDIS device, 02:5b:53:31:37:31
Wed Jul  5 22:22:41 2017 kern.info kernel: [   13.461807] usbcore: registered new interface driver rndis_host
Wed Jul  5 22:22:41 2017 kern.info kernel: [   13.922244] brcmsmac bcma0:1: mfg 4bf core 812 rev 17 class 0 irq 3
Wed Jul  5 22:22:41 2017 kern.err kernel: [   13.928938] ieee80211 phy0: wl0: brcms_b_attach: Unsupported Broadcom board type (0xb4cf) or revision level (0x0)
Wed Jul  5 22:22:41 2017 kern.err kernel: [   13.939483] ieee80211 phy0: wl0: brcms_b_attach: failed with err 15
Wed Jul  5 22:22:41 2017 kern.err kernel: [   13.945869] ieee80211 phy0: wl0: brcms_c_attach: failed with err 15
Wed Jul  5 22:22:41 2017 kern.err kernel: [   13.952317] ieee80211 phy0: brcmsmac: attach() failed with code 15
Wed Jul  5 22:22:41 2017 kern.err kernel: [   13.958605] brcmsmac: brcms_bcma_probe: brcms_attach failed!
Wed Jul  5 22:22:41 2017 kern.info kernel: [   13.964536] brcmsmac bcma1:1: mfg 4bf core 812 rev 23 class 0 irq 6
Wed Jul  5 22:22:41 2017 kern.debug kernel: [   13.971222] bcma: bus1: Switched to core: 0x812
Wed Jul  5 22:22:41 2017 kern.err kernel: [   13.971613] ieee80211 phy1: wl0: brcms_b_attach: Unsupported Broadcom board type (0xb4cf) or revision level (0x0)
Wed Jul  5 22:22:41 2017 kern.err kernel: [   13.982136] ieee80211 phy1: wl0: brcms_b_attach: failed with err 15
Wed Jul  5 22:22:41 2017 kern.err kernel: [   13.988517] ieee80211 phy1: wl0: brcms_c_attach: failed with err 15
Wed Jul  5 22:22:41 2017 kern.err kernel: [   13.994965] ieee80211 phy1: brcmsmac: attach() failed with code 15
Wed Jul  5 22:22:41 2017 kern.err kernel: [   14.001311] brcmsmac: brcms_bcma_probe: brcms_attach failed!
Wed Jul  5 22:22:41 2017 user.info kernel: [   14.026333] kmodloader: done loading kernel modules from /etc/modules.d/*
Wed Jul  5 22:22:44 2017 user.notice : Added device handler type: tunnel
Wed Jul  5 22:22:44 2017 user.notice : Added device handler type: Network device
Wed Jul  5 22:22:44 2017 user.notice : Added device handler type: bridge
Wed Jul  5 22:22:44 2017 user.notice : Added device handler type: veth
Wed Jul  5 22:22:44 2017 user.notice : Added device handler type: macvlan
Wed Jul  5 22:22:44 2017 user.notice : Added device handler type: 8021ad
Wed Jul  5 22:22:44 2017 user.notice : Added device handler type: 8021q
Wed Jul  5 22:22:47 2017 authpriv.info dropbear[750]: Not backgrounding
Wed Jul  5 22:22:50 2017 kern.info kernel: [   24.261412] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Wed Jul  5 22:22:50 2017 kern.info kernel: [   24.286504] device eth0.1 entered promiscuous mode
Wed Jul  5 22:22:50 2017 kern.info kernel: [   24.291519] device eth0 entered promiscuous mode
Wed Jul  5 22:22:50 2017 daemon.notice netifd: Interface 'lan' is enabled
Wed Jul  5 22:22:50 2017 kern.info kernel: [   24.312573] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
Wed Jul  5 22:22:50 2017 daemon.notice netifd: Interface 'lan' is setting up now
Wed Jul  5 22:22:50 2017 daemon.notice netifd: Interface 'lan' is now up
Wed Jul  5 22:22:50 2017 daemon.notice netifd: Interface 'loopback' is enabled
Wed Jul  5 22:22:50 2017 daemon.notice netifd: Interface 'loopback' is setting up now
Wed Jul  5 22:22:50 2017 daemon.notice netifd: Interface 'loopback' is now up
Wed Jul  5 22:22:50 2017 daemon.notice netifd: Interface 'usb' is enabled
Wed Jul  5 22:22:50 2017 kern.info kernel: [   24.442951] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
Wed Jul  5 22:22:50 2017 daemon.notice netifd: Interface 'wan' is enabled
Wed Jul  5 22:22:50 2017 daemon.notice netifd: Interface 'wan6' is enabled
Wed Jul  5 22:22:50 2017 daemon.notice netifd: Network device 'lo' link is up
Wed Jul  5 22:22:50 2017 daemon.notice netifd: Interface 'loopback' has link connectivity 
Wed Jul  5 22:22:50 2017 daemon.notice netifd: Network device 'usb0' link is up
Wed Jul  5 22:22:50 2017 daemon.notice netifd: Interface 'usb' has link connectivity 
Wed Jul  5 22:22:50 2017 daemon.notice netifd: Interface 'usb' is setting up now
Wed Jul  5 22:22:50 2017 daemon.notice netifd: usb (844): udhcpc: started, v1.26.2
Wed Jul  5 22:22:51 2017 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Wed Jul  5 22:22:51 2017 daemon.notice netifd: usb (844): udhcpc: sending discover
Wed Jul  5 22:22:51 2017 daemon.notice netifd: Network device 'eth0' link is up
Wed Jul  5 22:22:51 2017 kern.info kernel: [   25.639559] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Wed Jul  5 22:22:51 2017 kern.info kernel: [   25.699543] br-lan: port 1(eth0.1) entered forwarding state
Wed Jul  5 22:22:51 2017 kern.info kernel: [   25.705336] br-lan: port 1(eth0.1) entered forwarding state
Wed Jul  5 22:22:51 2017 kern.info kernel: [   25.711336] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
Wed Jul  5 22:22:51 2017 daemon.notice netifd: VLAN 'eth0.1' link is up
Wed Jul  5 22:22:51 2017 daemon.notice netifd: VLAN 'eth0.2' link is up
Wed Jul  5 22:22:51 2017 daemon.notice netifd: Interface 'wan' has link connectivity 
Wed Jul  5 22:22:51 2017 daemon.notice netifd: Interface 'wan' is setting up now
Wed Jul  5 22:22:51 2017 daemon.notice netifd: Interface 'wan6' has link connectivity 
Wed Jul  5 22:22:51 2017 daemon.notice netifd: bridge 'br-lan' link is up
Wed Jul  5 22:22:51 2017 daemon.notice netifd: Interface 'lan' has link connectivity 
Wed Jul  5 22:22:51 2017 kern.info kernel: [   25.764246] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Wed Jul  5 22:22:51 2017 daemon.notice netifd: wan (877): udhcpc: started, v1.26.2
Wed Jul  5 22:22:52 2017 daemon.notice netifd: wan (877): udhcpc: sending discover
Wed Jul  5 22:22:52 2017 daemon.warn odhcpd[706]: DHCPV6 CONFIRM IA_NA from 000437e7143d006c0d83f363f544b6c68c5f on br-lan: not on-link 
Wed Jul  5 22:22:53 2017 kern.info kernel: [   27.699340] br-lan: port 1(eth0.1) entered forwarding state
Wed Jul  5 22:22:54 2017 daemon.err ntpdate[781]: name server cannot be used: Try again (-3)
Wed Jul  5 22:22:54 2017 daemon.notice netifd: usb (844): udhcpc: sending discover
Wed Jul  5 22:22:54 2017 authpriv.info dropbear[909]: Child connection from 192.168.65.102:53976
Wed Jul  5 22:22:55 2017 daemon.notice netifd: wan (877): udhcpc: sending discover
Wed Jul  5 22:22:57 2017 daemon.notice netifd: usb (844): udhcpc: sending discover
Wed Jul  5 22:22:57 2017 daemon.info dnsmasq[947]: started, version 2.77 cachesize 150
Wed Jul  5 22:22:57 2017 daemon.info dnsmasq[947]: DNS service limited to local subnets
Wed Jul  5 22:22:57 2017 daemon.info dnsmasq[947]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC no-ID loop-detect inotify
Wed Jul  5 22:22:57 2017 daemon.info dnsmasq-dhcp[947]: DHCP, IP range 192.168.65.100 -- 192.168.65.249, lease time 12h
Wed Jul  5 22:22:57 2017 daemon.info dnsmasq[947]: using local addresses only for domain test
Wed Jul  5 22:22:57 2017 daemon.info dnsmasq[947]: using local addresses only for domain onion
Wed Jul  5 22:22:57 2017 daemon.info dnsmasq[947]: using local addresses only for domain localhost
Wed Jul  5 22:22:57 2017 daemon.info dnsmasq[947]: using local addresses only for domain local
Wed Jul  5 22:22:57 2017 daemon.info dnsmasq[947]: using local addresses only for domain invalid
Wed Jul  5 22:22:57 2017 daemon.info dnsmasq[947]: using local addresses only for domain example.net
Wed Jul  5 22:22:57 2017 daemon.info dnsmasq[947]: using local addresses only for domain example.org
Wed Jul  5 22:22:57 2017 daemon.info dnsmasq[947]: using local addresses only for domain example.com
Wed Jul  5 22:22:57 2017 daemon.info dnsmasq[947]: using 3 more local addresses
Wed Jul  5 22:22:57 2017 daemon.info dnsmasq[947]: reading /tmp/resolv.conf.auto
Wed Jul  5 22:22:57 2017 daemon.info dnsmasq[947]: using local addresses only for domain test
Wed Jul  5 22:22:57 2017 daemon.info dnsmasq[947]: using local addresses only for domain onion
Wed Jul  5 22:22:57 2017 daemon.info dnsmasq[947]: using local addresses only for domain localhost
Wed Jul  5 22:22:57 2017 daemon.info dnsmasq[947]: using local addresses only for domain local
Wed Jul  5 22:22:57 2017 daemon.info dnsmasq[947]: using local addresses only for domain invalid
Wed Jul  5 22:22:57 2017 daemon.info dnsmasq[947]: using local addresses only for domain example.net
Wed Jul  5 22:22:57 2017 daemon.info dnsmasq[947]: using local addresses only for domain example.org
Wed Jul  5 22:22:57 2017 daemon.info dnsmasq[947]: using local addresses only for domain example.com
Wed Jul  5 22:22:57 2017 daemon.info dnsmasq[947]: using nameserver 8.8.8.8#53
Wed Jul  5 22:22:57 2017 daemon.info dnsmasq[947]: using nameserver 8.8.4.4#53
Wed Jul  5 22:22:57 2017 daemon.info dnsmasq[947]: using 3 more local addresses
Wed Jul  5 22:22:57 2017 daemon.info dnsmasq[947]: read /etc/hosts - 4 addresses
Wed Jul  5 22:22:57 2017 daemon.info dnsmasq[947]: read /tmp/hosts/odhcpd - 0 addresses
Wed Jul  5 22:22:57 2017 daemon.info dnsmasq[947]: read /tmp/hosts/dhcp.cfg02411c - 3 addresses
Wed Jul  5 22:22:57 2017 daemon.info dnsmasq-dhcp[947]: read /etc/ethers - 0 addresses
Wed Jul  5 22:22:58 2017 daemon.notice netifd: wan (877): udhcpc: sending discover
Wed Jul  5 22:22:59 2017 daemon.err ntpdate[906]: name server cannot be used: Try again (-3)
Wed Jul  5 22:23:03 2017 daemon.info dnsmasq-dhcp[947]: DHCPDISCOVER(br-lan) 192.168.65.102 3c:97:0e:73:9c:4f 
Wed Jul  5 22:23:03 2017 daemon.info dnsmasq-dhcp[947]: DHCPOFFER(br-lan) 192.168.65.101 3c:97:0e:73:9c:4f 
Wed Jul  5 22:23:03 2017 daemon.info dnsmasq-dhcp[947]: DHCPREQUEST(br-lan) 192.168.65.101 3c:97:0e:73:9c:4f 
Wed Jul  5 22:23:03 2017 daemon.info dnsmasq-dhcp[947]: DHCPACK(br-lan) 192.168.65.101 3c:97:0e:73:9c:4f jessica-mate
Wed Jul  5 22:23:04 2017 daemon.err ntpdate[950]: name server cannot be used: Try again (-3)

[ dmesg ]
[    0.000000] Linux version 4.4.74 (buildbot@builds) (gcc version 5.4.0 (LEDE GCC 5.4.0 r4456-d98cafc) ) #0 Sun Jul 2 21:10:06 2017
[    0.000000] CPU0 revision is: 00019740 (MIPS 74Kc)
[    0.000000] bcm47xx: Using bcma bus
[    0.000000] bcma: bus0: Found chip with id 0x4716, rev 0x01 and package 0x0A
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000]   HighMem  empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 803a64c0, node_mem_map 81000000
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16384 pages, LIFO batch:3
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 60556K/65536K available (3002K kernel code, 134K rwdata, 696K rodata, 188K init, 294K bss, 4980K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:128
[    0.000000] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x1F, class 0x0)
[    0.000000] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x11, class 0x0)
[    0.000000] bcma: bus0: Core 2 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x00, class 0x0)
[    0.000000] bcma: bus0: Core 3 found: MIPS 74K (manuf 0x4A7, id 0x82C, rev 0x01, class 0x0)
[    0.000000] bcma: bus0: Core 4 found: USB 2.0 Host (manuf 0x4BF, id 0x819, rev 0x04, class 0x0)
[    0.000000] bcma: bus0: Core 5 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0E, class 0x0)
[    0.000000] bcma: bus0: Core 6 found: DDR1/DDR2 Memory Controller (manuf 0x4BF, id 0x82E, rev 0x01, class 0x0)
[    0.000000] bcma: bus0: Core 7 found: Internal Memory (manuf 0x4BF, id 0x80E, rev 0x07, class 0x0)
[    0.000000] bcma: bus0: Core 8 found: I2S (manuf 0x4BF, id 0x834, rev 0x00, class 0x0)
[    0.000000] bcma: bus0: Found rev 5 PMU (capabilities 0x11242C05)
[    0.000000] bcma: bus0: Found serial flash
[    0.000000] bcma: bus0: Found M25P64 serial flash (size: 8192KiB, blocksize: 0x10000, blocks: 128)
[    0.000000] bcma: bus0: Early bus registered
[    0.000000] MIPS: machine is Unknown Board
[    0.000000] bcm47xx: Setting up vectored interrupts
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 8438235966 ns
[    0.000015] sched_clock: 32 bits at 226MHz, resolution 4ns, wraps every 9481163773ns
[    0.000088] Calibrating delay loop... 226.09 BogoMIPS (lpj=1130496)
[    0.070063] pid_max: default: 32768 minimum: 301
[    0.070318] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.070345] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.074642] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.074715] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.076193] NET: Registered protocol family 16
[    0.099321] clocksource: Switched to clocksource MIPS
[    0.101966] NET: Registered protocol family 2
[    0.103621] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.103678] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.103719] TCP: Hash tables configured (established 1024 bind 1024)
[    0.103896] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.103944] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.104461] NET: Registered protocol family 1
[    0.104612] PCI: CLS 0 bytes, default 32
[    0.113504] bcma: bus0: Using SPROM revision 0 provided by platform.
[    0.113545] bcma: bus0: PMU resource config unknown or not needed for device 0x4716
[    0.115561] bcma: bus0: Workarounds unknown or not needed for device 0x4716
[    0.115580] bcma: bus0: Initializing MIPS core...
[    0.115601] bcma: bus0: Moved i2s interrupt to oob line 7 instead of 8
[    0.115628] bcma: bus0: set_irq: core 0x0812, irq 3 => 3
[    0.115651] bcma: bus0: set_irq: core 0x082d, irq 4 => 4
[    0.115674] bcma: bus0: set_irq: core 0x0819, irq 5 => 5
[    0.115697] bcma: bus0: set_irq: core 0x0820, irq 6 => 6
[    0.115718] bcma: bus0: set_irq: core 0x0800, irq 2 => 2
[    0.115741] bcma: bus0: set_irq: core 0x0834, irq 0 => 2
[    0.115756] bcma: bus0: IRQ reconfiguration done
[    0.115772] bcma: core 0x0800, irq : 2(S)* 3  4  5  6  D  I 
[    0.115825] bcma: core 0x0812, irq : 2(S)  3* 4  5  6  D  I 
[    0.115869] bcma: core 0x082d, irq : 2(S)  3  4* 5  6  D  I 
[    0.115913] bcma: core 0x082c, irq : 2(S)  3  4  5  6  D  I*
[    0.115957] bcma: core 0x0819, irq : 2(S)  3  4  5* 6  D  I 
[    0.116001] bcma: core 0x0820, irq : 2(S)  3  4  5  6* D  I 
[    0.116045] bcma: core 0x082e, irq : 2(S)  3  4  5  6  D* I 
[    0.116088] bcma: core 0x080e, irq : 2(S)  3  4  5  6  D  I*
[    0.116130] bcma: core 0x0834, irq : 2(S)* 3  4  5  6  D  I 
[    0.116176] bcma: bus0: PCIEcore in host mode found
[    0.304669] PCI host bridge to bus 0000:00
[    0.304727] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0bffffff]
[    0.304756] pci_bus 0000:00: root bus resource [io  0x0100-0x07ff]
[    0.304785] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.304814] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.304903] pci 0000:00:00.0: [14e4:4716] type 00 class 0x060000
[    0.304948] bcma: PCI: Fixing up bridge 0000:00:00.0
[    0.304969] bcma: PCI: Fixing up device 0000:00:00.0
[    0.305033] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit]
[    0.305073] pci 0000:00:00.0: reg 0x18: [mem 0x00000000-0x07ffffff 64bit]
[    0.305187] pci 0000:00:00.0: supports D1 D2
[    0.305595] pci 0000:00:00.1: [14e4:0000] type 00 class 0x060000
[    0.305645] bcma: PCI: Fixing up bridge 0000:00:00.1
[    0.305666] bcma: PCI: Fixing up device 0000:00:00.1
[    0.305731] pci 0000:00:00.1: reg 0x10: [mem 0x00000000-0x00003fff 64bit]
[    0.305770] pci 0000:00:00.1: reg 0x18: [mem 0x00000000-0x07ffffff 64bit]
[    0.305878] pci 0000:00:00.1: supports D1 D2
[    0.306355] pci 0000:00:01.0: [14e4:a8d8] type 00 class 0x028000
[    0.306490] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit]
[    0.306593] bcma: PCI: Fixing up addresses 0000:00:01.0
[    0.306642] pci 0000:00:01.0: BAR 0: assigned [mem 0x08000000-0x08003fff 64bit]
[    0.306809] pci 0000:00:01.0: supports D1 D2
[    0.307254] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    0.308856] bcma: bus0: Bus registered
[    0.310393] Crashlog allocated RAM at address 0x3f00000
[    0.344150] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.344205] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.349655] io scheduler noop registered
[    0.349707] io scheduler deadline registered (default)
[    0.350248] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.355394] console [ttyS0] disabled
[    0.375653] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 2, base_baud = 1250000) is a U6_16550A
[    0.872455] console [ttyS0] enabled
[    0.989922] 7 bcm47xxpart partitions found on MTD device bcm47xxsflash
[    0.996576] Creating 7 MTD partitions on "bcm47xxsflash":
[    1.002140] 0x000000000000-0x000000040000 : "boot"
[    1.011599] 0x000000040000-0x0000007e0000 : "firmware"
[    1.020126] 0x0000007e0000-0x0000007f0000 : "board_data"
[    1.028709] 0x0000007f0000-0x000000800000 : "nvram"
[    1.036956] 0x00000004001c-0x000000040920 : "loader"
[    1.045355] 0x000000040920-0x00000017dc00 : "linux"
[    1.053621] 0x00000017dc00-0x0000007e0000 : "rootfs"
[    1.061906] mtd: device 6 (rootfs) set to be root filesystem
[    1.067729] 1 squashfs-split partitions found on MTD device rootfs
[    1.074136] 0x000000360000-0x0000007e0000 : "rootfs_data"
[    1.086521] libphy: Fixed MDIO Bus: probed
[    1.091101] bgmac_bcma bcma0:2: Found PHY addr: 30 (NOREGS)
[    1.100515] libphy: bcma_mdio mii bus: probed
[    1.104979] bgmac_bcma bcma0:2: Support for Roboswitch not implemented
[    1.264041] b53_common: found switch: BCM5325, rev 0
[    1.270621] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded
[    1.276982] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds)
[    1.285141] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[    1.291021] bcma: PCI: Fixing up device 0000:00:01.0
[    1.296150] bcma: bus1: Found chip with id 43224, rev 0x01 and package 0x08
[    1.303351] bcma: bus1: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x22, class 0x0)
[    1.312133] bcma: bus1: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x17, class 0x0)
[    1.321015] bcma: bus1: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0F, class 0x0)
[    1.329246] bcma: bus1: Found rev 6 PMU (capabilities 0x108C2606)
[    1.330088] bcma: bus1: Using SPROM revision 0 provided by platform.
[    1.330132] bcma: bus1: PMU resource config unknown or not needed for device 0xA8D8
[    1.340850] bcma: bus1: Bus registered
[    1.346903] NET: Registered protocol family 10
[    1.357396] NET: Registered protocol family 17
[    1.362216] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    1.375148] 8021q: 802.1Q VLAN Support v1.8
[    1.393155] VFS: Mounted root (squashfs filesystem) readonly on device 31:6.
[    1.401759] Freeing unused kernel memory: 188K (803c1000 - 803f0000)
[    3.050931] init: Console is alive
[    3.054861] init: - watchdog -
[    4.254646] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    4.402007] usbcore: registered new interface driver usbfs
[    4.407764] usbcore: registered new interface driver hub
[    4.413517] usbcore: registered new device driver usb
[    4.427524] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.437246] ehci-platform: EHCI generic platform driver
[    4.442860] ehci-platform ehci-platform.0: EHCI Host Controller
[    4.449006] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[    4.457485] ehci-platform ehci-platform.0: irq 5, io mem 0x18004000
[    4.479401] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
[    4.487835] hub 1-0:1.0: USB hub found
[    4.492481] hub 1-0:1.0: 2 ports detected
[    4.502125] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    4.510967] ohci-platform: OHCI generic platform driver
[    4.516448] ohci-platform ohci-platform.0: Generic Platform OHCI controller
[    4.523735] ohci-platform ohci-platform.0: new USB bus registered, assigned bus number 2
[    4.532182] ohci-platform ohci-platform.0: irq 5, io mem 0x18009000
[    4.595330] hub 2-0:1.0: USB hub found
[    4.600124] hub 2-0:1.0: 2 ports detected
[    4.608697] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    4.626861] init: - preinit -
[    5.011347] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    5.263503] random: procd: uninitialized urandom read (4 bytes read, 9 bits of entropy available)
[    6.414938] random: jshn: uninitialized urandom read (4 bytes read, 11 bits of entropy available)
[    6.608349] random: jshn: uninitialized urandom read (4 bytes read, 11 bits of entropy available)
[    6.731613] random: jshn: uninitialized urandom read (4 bytes read, 11 bits of entropy available)
[    7.012119] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    7.018248] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[    8.569470] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    8.576495] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[   10.681655] jffs2: notice: (375) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   10.705445] mount_root: switching to jffs2 overlay
[   10.759409] urandom-seed: Seeding with /etc/urandom.seed
[   10.971431] procd: - early -
[   10.974613] procd: - watchdog -
[   11.730144] procd: - watchdog -
[   11.734119] procd: - ubus -
[   11.756070] random: ubusd: uninitialized urandom read (4 bytes read, 20 bits of entropy available)
[   11.789743] random: ubusd: uninitialized urandom read (4 bytes read, 20 bits of entropy available)
[   11.799846] random: ubusd: uninitialized urandom read (4 bytes read, 20 bits of entropy available)
[   11.809088] random: ubusd: uninitialized urandom read (4 bytes read, 20 bits of entropy available)
[   11.819720] random: ubusd: uninitialized urandom read (4 bytes read, 20 bits of entropy available)
[   11.828937] random: ubusd: uninitialized urandom read (4 bytes read, 20 bits of entropy available)
[   11.840154] procd: - init -
[   13.039395] kmodloader: loading kernel modules from /etc/modules.d/*
[   13.065020] tun: Universal TUN/TAP device driver, 1.6
[   13.070278] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   13.085691] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   13.145711] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
[   13.153955] Backport generated by backports.git backports-20160324-13-g24da7d3c
[   13.171588] ip_tables: (C) 2000-2006 Netfilter Core Team
[   13.193691] nf_conntrack version 0.5.0 (949 buckets, 3796 max)
[   13.317055] xt_time: kernel timezone is -0000
[   13.325369] usbcore: registered new interface driver cdc_ether
[   13.427171] PPP generic driver version 2.4.2
[   13.436494] NET: Registered protocol family 24
[   13.450675] rndis_host 1-1:1.0 usb0: register 'rndis_host' at usb-ehci-platform.0-1, RNDIS device, 02:5b:53:31:37:31
[   13.461807] usbcore: registered new interface driver rndis_host
[   13.922244] brcmsmac bcma0:1: mfg 4bf core 812 rev 17 class 0 irq 3
[   13.928938] ieee80211 phy0: wl0: brcms_b_attach: Unsupported Broadcom board type (0xb4cf) or revision level (0x0)
[   13.939483] ieee80211 phy0: wl0: brcms_b_attach: failed with err 15
[   13.945869] ieee80211 phy0: wl0: brcms_c_attach: failed with err 15
[   13.952317] ieee80211 phy0: brcmsmac: attach() failed with code 15
[   13.958605] brcmsmac: brcms_bcma_probe: brcms_attach failed!
[   13.964536] brcmsmac bcma1:1: mfg 4bf core 812 rev 23 class 0 irq 6
[   13.971222] bcma: bus1: Switched to core: 0x812
[   13.971613] ieee80211 phy1: wl0: brcms_b_attach: Unsupported Broadcom board type (0xb4cf) or revision level (0x0)
[   13.982136] ieee80211 phy1: wl0: brcms_b_attach: failed with err 15
[   13.988517] ieee80211 phy1: wl0: brcms_c_attach: failed with err 15
[   13.994965] ieee80211 phy1: brcmsmac: attach() failed with code 15
[   14.001311] brcmsmac: brcms_bcma_probe: brcms_attach failed!
[   14.026333] kmodloader: done loading kernel modules from /etc/modules.d/*
[   24.261412] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   24.286504] device eth0.1 entered promiscuous mode
[   24.291519] device eth0 entered promiscuous mode
[   24.312573] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   24.442951] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[   25.639559] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   25.699543] br-lan: port 1(eth0.1) entered forwarding state
[   25.705336] br-lan: port 1(eth0.1) entered forwarding state
[   25.711336] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[   25.764246] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   27.699340] br-lan: port 1(eth0.1) entered forwarding state
[   61.049212] random: nonblocking pool is initialized

00:01.0 Network controller: Broadcom Limited BCM43224/5 Wireless Network Adapter (rev 01)
	Subsystem: Broadcom Limited BCM43224/5 Wireless Network Adapter
	Flags: bus master, fast devsel, latency 0, IRQ 6
	Memory at 08000000 (64-bit, non-prefetchable) [size=16385]
	Memory at <unassigned> (32-bit, non-prefetchable) [size=2]
	Memory at <unassigned> (32-bit, non-prefetchable) [size=2]
	Memory at <unassigned> (32-bit, non-prefetchable) [size=2]
	Memory at <unassigned> (32-bit, non-prefetchable) [size=2]
	Expansion ROM at <unassigned> [disabled] [size=2]
	Capabilities: [40] Power Management version 3
	Capabilities: [58] Vendor Specific Information: Len=78 <?>
	Capabilities: [48] MSI: Enable- Count=1/1 Maskable- 64bit+
	Capabilities: [d0] Express Endpoint, MSI 00
	Capabilities: [100] Advanced Error Reporting
	Capabilities: [13c] Virtual Channel
	Capabilities: [160] Device Serial Number 00-00-00-ff-ff-00-00-00
	Capabilities: [16c] Power Budgeting <?>
	Kernel driver in use: bcma-pci-bridge


13.06.2017844Base systemBug ReportVery LowHighWMM Mode bug with Wifi 2,4Ghz Archer C7 1750 V2 with L...lede-17.01Unconfirmed Task Description

Hi,

I meet a bug with certain ring roads(peripherals) (Xbox 360 and Epson SX425) using the WiFi 2,4Ghz of my TP(PRACTICAL CLASS) Link Archer C7 1750 under LEDE 17.01.2 (noticed also with LEDE 17.01.1) with activated WMM mode.

When WMM mode is active ring roads(peripherals) Xbox 360 and Epson SX425 does not receive an IP address while quite my other PC works carefree in WiFi 2,4Ghz.

By deactivating WMM mode and by restarting the router(route planner) everything works perfectly.

I specify that with OpenWrt 15.05.1 WMM Mode worked perfectly.

08.04.2017692Base systemBug ReportMediumMediumWLAN AP not working on RasPi (bcm2710 target)TrunkAssigned Task Description

When flashing the brcm2708 / bcm2710 target the WiFi interface gets stuck in “client mode” and the AP will not be able to be brought up.

Some screenshots and a load of discussion here:
https://forum.lede-project.org/t/ap-mode-radio0-in-raspi-3-always-acts-as-a-client-shows-as-wlan0-in-luci/2885

Two more days of tinkering, wifi-up’ing and -down’ing did not bring me further.
I flashed another Pi3 (to exclude a hardware defect) with the same result.

I tried latest snapshot and stable images.
I am happy to help debug – tell me what you need me to do.

Greetings,
–Thomas

24.10.20171110Base systemBug ReportVery LowLowWifi unusable on HG556a using current trunkTrunkUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on: Huawei ECHOLIFE HG556a Type B
- Software versions of LEDE release, packages, etc: Current Trunk - Powered by LuCI Master (git-17.294.24601-59a4e40) / LEDE Reboot SNAPSHOT r5122-f7a6fd3153

- Steps to reproduce: reboot

I did an update to trunk and made a lede build for the HG556a type B the other day. I have two of these HG556a type B routers both configured as wireless repeaters. I made no changes to the config, I simply wanted the latest security patches installed on my wifi repeaters. The first HG556a connects to a WWAN router that broadcasts 802.11n only, the other WWAN router broadcasts legacy wifi modes and 802.11n. The first works perfectly. The second throws up numerous errors in syslog from boot time, reboot every few hours and repeatedly disconnects from clients and the WWAN router. See syslog below:

Powered by LuCI Master (git-17.294.24601-59a4e40) / LEDE Reboot SNAPSHOT r5122-f7a6fd3153

Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.596484] CPU: 0 PID: 1399 Comm: wpa_supplicant Tainted: G W 4.4.93 #0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.604568] Stack : 80546d42 00000049 00000000 803f0000 82f116a4 803e6da3 80372ae0 00000577
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.604568] 80543fac 00000000 00000004 81f73908 00000000 800594cc 8037d094 803e0000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.604568] 00000000 00000000 8037b4a0 82f0f8d4 00000000 800573d0 80546d42 00000072
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.604568] 803e5e50 801bdc00 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.604568] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.604568] ...
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.641077] Call Trace:
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.643652] [<80024f84>] show_stack+0×54/0×88 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.648182] [<80032f00>] warn_slowpath_common+0xa0/0xd0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.653588] [<80032fb8>] warn_slowpath_null+0×18/0×24 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.659056] [<82c262e4>] ieee80211_rx_napi+0×240/0x97c [mac80211]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.665646] [<832c7260>] ath_rx_tasklet+0xc24/0xc88 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.671458] [<832c733c>] ath_stoprecv+0×78/0xf34 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.676979] [<832c3230>] ath9k_deinit_device+0x6d0/0×944 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.683219] [<832c503c>] ath9k_calculate_summary_state+0×500/0×600 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.690367]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.691843] —[ end trace 0902623f520cb0c7 ]— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.698309] ————[ cut here ]———— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.703376] WARNING: CPU: 0 PID: 1399 at backports-2017-10-06/net/mac80211/rx.c:629 ieee80211_rx_napi+0×240/0x97c [mac80211]()
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.715140] Modules linked in: ath9k ath9k_htc ath9k_common pppoe ppp_async option cdc_mbim ath9k_hw ath usb_wwan rndis_host qmi_wwan pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE huawei_cdc_ncm cfg80211 cdc_subset cdc_ncm cdc_ether cdc_eem xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state xt_recent xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_cTue Oct 24 13:08:04 2017 kern.warn kernel: [19932.858376] CPU: 0 PID: 1399 Comm: wpa_supplicant Tainted: G W 4.4.93 #0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.866468] Stack : 80546d42 00000049 00000000 803f0000 82f116a4 803e6da3 80372ae0 00000577
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.866468] 80543fac 00000000 00000004 81f76648 00000000 800594cc 8037d094 803e0000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.866468] 00000000 00000000 8037b4a0 82f0f8d4 00000000 800573d0 80546d42 00000072
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.866468] 803e5e50 801bdc00 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.866468] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.866468] ...
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.902968] Call Trace:
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.905544] [<80024f84>] show_stack+0×54/0×88 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.910072] [<80032f00>] warn_slowpath_common+0xa0/0xd0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.915479] [<80032fb8>] warn_slowpath_null+0×18/0×24 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.920933] [<82c262e4>] ieee80211_rx_napi+0×240/0x97c [mac80211]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.927490] [<832c7260>] ath_rx_tasklet+0xc24/0xc88 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.933304] [<832c733c>] ath_stoprecv+0×78/0xf34 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.938829] [<832c3230>] ath9k_deinit_device+0x6d0/0×944 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.945064] [<832c503c>] ath9k_calculate_summary_state+0×500/0×600 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.952230]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.953769] —[ end trace 0902623f520cb0c8 ]— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.958850] ————[ cut here ]———— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.963902] WARNING: CPU: 0 PID: 1399 at backports-2017-10-06/net/mac80211/rx.c:629 ieee80211_rx_napi+0×240/0x97c [mac80211]()
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19932.975678] Modules linked in: ath9k ath9k_htc ath9k_common pppoe ppp_async option cdc_mbim ath9k_hw ath usb_wwan rndis_host qmi_wwan pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE huawei_cdc_ncm cfg80211 cdc_subset cdc_ncm cdc_ether cdc_eem xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state xt_recent xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_cTue Oct 24 13:08:04 2017 kern.warn kernel: [19933.118913] CPU: 0 PID: 1399 Comm: wpa_supplicant Tainted: G W 4.4.93 #0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.126999] Stack : 80546d42 00000049 00000000 803f0000 82f116a4 803e6da3 80372ae0 00000577
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.126999] 80543fac 00000000 00000004 81f76b18 00000000 800594cc 8037d094 803e0000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.126999] 00000000 00000000 8037b4a0 82f0f8d4 00000000 800573d0 80546d42 00000072
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.126999] 803e5e50 801bdc00 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.126999] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.126999] ...
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.163508] Call Trace:
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.166083] [<80024f84>] show_stack+0×54/0×88 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.170613] [<80032f00>] warn_slowpath_common+0xa0/0xd0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.176018] [<80032fb8>] warn_slowpath_null+0×18/0×24 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.181482] [<82c262e4>] ieee80211_rx_napi+0×240/0x97c [mac80211]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.188060] [<832c7260>] ath_rx_tasklet+0xc24/0xc88 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.193877] [<832c733c>] ath_stoprecv+0×78/0xf34 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.199401] [<832c3230>] ath9k_deinit_device+0x6d0/0×944 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.205641] [<832c503c>] ath9k_calculate_summary_state+0×500/0×600 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.212796]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.214330] —[ end trace 0902623f520cb0c9 ]— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.219582] ————[ cut here ]———— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.224643] WARNING: CPU: 0 PID: 1399 at backports-2017-10-06/net/mac80211/rx.c:629 ieee80211_rx_napi+0×240/0x97c [mac80211]()
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.236421] Modules linked in: ath9k ath9k_htc ath9k_common pppoe ppp_async option cdc_mbim ath9k_hw ath usb_wwan rndis_host qmi_wwan pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE huawei_cdc_ncm cfg80211 cdc_subset cdc_ncm cdc_ether cdc_eem xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state xt_recent xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_cTue Oct 24 13:08:04 2017 kern.warn kernel: [19933.379658] CPU: 0 PID: 1399 Comm: wpa_supplicant Tainted: G W 4.4.93 #0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.387752] Stack : 80546d42 00000049 00000000 803f0000 82f116a4 803e6da3 80372ae0 00000577
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.387752] 80543fac 00000000 00000004 81e79bc8 00000000 800594cc 8037d094 803e0000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.387752] 00000000 00000000 8037b4a0 82f0f8d4 00000000 800573d0 80546d42 00000072
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.387752] 803e5e50 801bdc00 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.387752] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.387752] ...
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.424254] Call Trace:
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.426828] [<80024f84>] show_stack+0×54/0×88 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.431359] [<80032f00>] warn_slowpath_common+0xa0/0xd0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.436764] [<80032fb8>] warn_slowpath_null+0×18/0×24 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.442218] [<82c262e4>] ieee80211_rx_napi+0×240/0x97c [mac80211]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.448774] [<832c7260>] ath_rx_tasklet+0xc24/0xc88 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.454587] [<832c733c>] ath_stoprecv+0×78/0xf34 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.460111] [<832c3230>] ath9k_deinit_device+0x6d0/0×944 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.466350] [<832c503c>] ath9k_calculate_summary_state+0×500/0×600 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.473507]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.474982] —[ end trace 0902623f520cb0ca ]— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.480524] ————[ cut here ]———— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.485601] WARNING: CPU: 0 PID: 1399 at backports-2017-10-06/net/mac80211/rx.c:629 ieee80211_rx_napi+0×240/0x97c [mac80211]()
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.497400] Modules linked in: ath9k ath9k_htc ath9k_common pppoe ppp_async option cdc_mbim ath9k_hw ath usb_wwan rndis_host qmi_wwan pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE huawei_cdc_ncm cfg80211 cdc_subset cdc_ncm cdc_ether cdc_eem xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state xt_recent xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_cTue Oct 24 13:08:04 2017 kern.warn kernel: [19933.640637] CPU: 0 PID: 1399 Comm: wpa_supplicant Tainted: G W 4.4.93 #0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.648719] Stack : 80546d42 00000049 00000000 803f0000 82f116a4 803e6da3 80372ae0 00000577
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.648719] 80543fac 00000000 00000004 82f334e8 00000000 800594cc 8037d094 803e0000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.648719] 00000000 00000000 8037b4a0 82f0f8d4 00000000 800573d0 80546d42 00000072
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.648719] 803e5e50 801bdc00 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.648719] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.648719] ...
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.685231] Call Trace:
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.687807] [<80024f84>] show_stack+0×54/0×88 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.692346] [<80032f00>] warn_slowpath_common+0xa0/0xd0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.697751] [<80032fb8>] warn_slowpath_null+0×18/0×24 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.703222] [<82c262e4>] ieee80211_rx_napi+0×240/0x97c [mac80211]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.709776] [<832c7260>] ath_rx_tasklet+0xc24/0xc88 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.715590] [<832c733c>] ath_stoprecv+0×78/0xf34 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.721115] [<832c3230>] ath9k_deinit_device+0x6d0/0×944 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.727354] [<832c503c>] ath9k_calculate_summary_state+0×500/0×600 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.734503]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.735978] —[ end trace 0902623f520cb0cb ]— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.741140] ————[ cut here ]———— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.746190] WARNING: CPU: 0 PID: 1399 at backports-2017-10-06/net/mac80211/rx.c:629 ieee80211_rx_napi+0×240/0x97c [mac80211]()
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.757949] Modules linked in: ath9k ath9k_htc ath9k_common pppoe ppp_async option cdc_mbim ath9k_hw ath usb_wwan rndis_host qmi_wwan pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE huawei_cdc_ncm cfg80211 cdc_subset cdc_ncm cdc_ether cdc_eem xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state xt_recent xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_cTue Oct 24 13:08:04 2017 kern.warn kernel: [19933.901184] CPU: 0 PID: 1399 Comm: wpa_supplicant Tainted: G W 4.4.93 #0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.909277] Stack : 80546d42 00000049 00000000 803f0000 82f116a4 803e6da3 80372ae0 00000577
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.909277] 80543fac 00000000 00000004 82f822d8 00000000 800594cc 8037d094 803e0000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.909277] 00000000 00000000 8037b4a0 82f0f8d4 00000000 800573d0 80546d42 00000072
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.909277] 803e5e50 801bdc00 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.909277] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.909277] ...
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.945779] Call Trace:
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.948307] [<80024f84>] show_stack+0×54/0×88 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.952874] [<80032f00>] warn_slowpath_common+0xa0/0xd0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.958280] [<80032fb8>] warn_slowpath_null+0×18/0×24 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.963731] [<82c262e4>] ieee80211_rx_napi+0×240/0x97c [mac80211]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.970280] [<832c7260>] ath_rx_tasklet+0xc24/0xc88 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.976092] [<832c733c>] ath_stoprecv+0×78/0xf34 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.981608] [<832c3230>] ath9k_deinit_device+0x6d0/0×944 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.987845] [<832c503c>] ath9k_calculate_summary_state+0×500/0×600 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.994995]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19933.996472] —[ end trace 0902623f520cb0cc ]— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.001802] ————[ cut here ]———— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.006851] WARNING: CPU: 0 PID: 1399 at backports-2017-10-06/net/mac80211/rx.c:629 ieee80211_rx_napi+0×240/0x97c [mac80211]()
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.018628] Modules linked in: ath9k ath9k_htc ath9k_common pppoe ppp_async option cdc_mbim ath9k_hw ath usb_wwan rndis_host qmi_wwan pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE huawei_cdc_ncm cfg80211 cdc_subset cdc_ncm cdc_ether cdc_eem xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state xt_recent xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_cTue Oct 24 13:08:04 2017 kern.warn kernel: [19934.161867] CPU: 0 PID: 1399 Comm: wpa_supplicant Tainted: G W 4.4.93 #0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.169949] Stack : 80546d42 00000049 00000000 803f0000 82f116a4 803e6da3 80372ae0 00000577
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.169949] 80543fac 00000000 00000004 82f82a68 00000000 800594cc 8037d094 803e0000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.169949] 00000000 00000000 8037b4a0 82f0f8d4 00000000 800573d0 80546d42 00000072
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.169949] 803e5e50 801bdc00 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.169949] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.169949] ...
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.206460] Call Trace:
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.208989] [<80024f84>] show_stack+0×54/0×88 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.213559] [<80032f00>] warn_slowpath_common+0xa0/0xd0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.218963] [<80032fb8>] warn_slowpath_null+0×18/0×24 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.224427] [<82c262e4>] ieee80211_rx_napi+0×240/0x97c [mac80211]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.230982] [<832c7260>] ath_rx_tasklet+0xc24/0xc88 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.236793] [<832c733c>] ath_stoprecv+0×78/0xf34 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.242310] [<832c3230>] ath9k_deinit_device+0x6d0/0×944 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.248546] [<832c503c>] ath9k_calculate_summary_state+0×500/0×600 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.255694]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.257173] —[ end trace 0902623f520cb0cd ]— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.263788] ————[ cut here ]———— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.268875] WARNING: CPU: 0 PID: 1399 at backports-2017-10-06/net/mac80211/rx.c:629 ieee80211_rx_napi+0×240/0x97c [mac80211]()
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.280640] Modules linked in: ath9k ath9k_htc ath9k_common pppoe ppp_async option cdc_mbim ath9k_hw ath usb_wwan rndis_host qmi_wwan pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE huawei_cdc_ncm cfg80211 cdc_subset cdc_ncm cdc_ether cdc_eem xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state xt_recent xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_cTue Oct 24 13:08:04 2017 kern.warn kernel: [19934.423875] CPU: 0 PID: 1399 Comm: wpa_supplicant Tainted: G W 4.4.93 #0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.431969] Stack : 80546d42 00000049 00000000 803f0000 82f116a4 803e6da3 80372ae0 00000577
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.431969] 80543fac 00000000 00000004 82f85598 00000000 800594cc 8037d094 803e0000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.431969] 00000000 00000000 8037b4a0 82f0f8d4 00000000 800573d0 80546d42 00000072
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.431969] 803e5e50 801bdc00 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.431969] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.431969] ...
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.468470] Call Trace:
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.471043] [<80024f84>] show_stack+0×54/0×88 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.475571] [<80032f00>] warn_slowpath_common+0xa0/0xd0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.480985] [<80032fb8>] warn_slowpath_null+0×18/0×24 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.486443] [<82c262e4>] ieee80211_rx_napi+0×240/0x97c [mac80211]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.492998] [<832c7260>] ath_rx_tasklet+0xc24/0xc88 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.498812] [<832c733c>] ath_stoprecv+0×78/0xf34 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.504334] [<832c3230>] ath9k_deinit_device+0x6d0/0×944 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.510574] [<832c503c>] ath9k_calculate_summary_state+0×500/0×600 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.517723]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.519198] —[ end trace 0902623f520cb0ce ]— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.524808] ————[ cut here ]———— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.529872] WARNING: CPU: 0 PID: 1399 at backports-2017-10-06/net/mac80211/rx.c:629 ieee80211_rx_napi+0×240/0x97c [mac80211]()
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.541651] Modules linked in: ath9k ath9k_htc ath9k_common pppoe ppp_async option cdc_mbim ath9k_hw ath usb_wwan rndis_host qmi_wwan pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE huawei_cdc_ncm cfg80211 cdc_subset cdc_ncm cdc_ether cdc_eem xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state xt_recent xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_cTue Oct 24 13:08:04 2017 kern.warn kernel: [19934.684889] CPU: 0 PID: 1399 Comm: wpa_supplicant Tainted: G W 4.4.93 #0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.692972] Stack : 80546d42 00000049 00000000 803f0000 82f116a4 803e6da3 80372ae0 00000577
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.692972] 80543fac 00000000 00000004 832f2f38 00000000 800594cc 8037d094 803e0000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.692972] 00000000 00000000 8037b4a0 82f0f8d4 00000000 800573d0 80546d42 00000072
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.692972] 803e5e50 801bdc00 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.692972] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.692972] ...
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.729518] Call Trace:
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.732012] [<80024f84>] show_stack+0×54/0×88 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.736580] [<80032f00>] warn_slowpath_common+0xa0/0xd0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.741986] [<80032fb8>] warn_slowpath_null+0×18/0×24 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.747459] [<82c262e4>] ieee80211_rx_napi+0×240/0x97c [mac80211]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.754014] [<832c7260>] ath_rx_tasklet+0xc24/0xc88 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.759824] [<832c733c>] ath_stoprecv+0×78/0xf34 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.765340] [<832c3230>] ath9k_deinit_device+0x6d0/0×944 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.771598] [<832c503c>] ath9k_calculate_summary_state+0×500/0×600 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.778745]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.780221] —[ end trace 0902623f520cb0cf ]— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.785086] ————[ cut here ]———— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.790094] WARNING: CPU: 0 PID: 1399 at backports-2017-10-06/net/mac80211/rx.c:629 ieee80211_rx_napi+0×240/0x97c [mac80211]()
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.801851] Modules linked in: ath9k ath9k_htc ath9k_common pppoe ppp_async option cdc_mbim ath9k_hw ath usb_wwan rndis_host qmi_wwan pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE huawei_cdc_ncm cfg80211 cdc_subset cdc_ncm cdc_ether cdc_eem xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state xt_recent xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_cTue Oct 24 13:08:04 2017 kern.warn kernel: [19934.945087] CPU: 0 PID: 1399 Comm: wpa_supplicant Tainted: G W 4.4.93 #0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.953182] Stack : 80546d42 00000049 00000000 803f0000 82f116a4 803e6da3 80372ae0 00000577
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.953182] 80543fac 00000000 00000004 82face88 00000000 800594cc 8037d094 803e0000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.953182] 00000000 00000000 8037b4a0 82f0f8d4 00000000 800573d0 80546d42 00000072
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.953182] 803e5e50 801bdc00 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.953182] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.953182] ...
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.989682] Call Trace:
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.992210] [<80024f84>] show_stack+0×54/0×88 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19934.996777] [<80032f00>] warn_slowpath_common+0xa0/0xd0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.002184] [<80032fb8>] warn_slowpath_null+0×18/0×24 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.007645] [<82c262e4>] ieee80211_rx_napi+0×240/0x97c [mac80211]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.014194] [<832c7260>] ath_rx_tasklet+0xc24/0xc88 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.020006] [<832c733c>] ath_stoprecv+0×78/0xf34 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.025529] [<832c3230>] ath9k_deinit_device+0x6d0/0×944 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.031769] [<832c503c>] ath9k_calculate_summary_state+0×500/0×600 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.038926]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.040402] —[ end trace 0902623f520cb0d0 ]— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.045585] ————[ cut here ]———— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.050620] WARNING: CPU: 0 PID: 1399 at backports-2017-10-06/net/mac80211/rx.c:629 ieee80211_rx_napi+0×240/0x97c [mac80211]()
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.062398] Modules linked in: ath9k ath9k_htc ath9k_common pppoe ppp_async option cdc_mbim ath9k_hw ath usb_wwan rndis_host qmi_wwan pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE huawei_cdc_ncm cfg80211 cdc_subset cdc_ncm cdc_ether cdc_eem xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state xt_recent xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_cTue Oct 24 13:08:04 2017 kern.warn kernel: [19935.205636] CPU: 0 PID: 1399 Comm: wpa_supplicant Tainted: G W 4.4.93 #0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.213720] Stack : 80546d42 00000049 00000000 803f0000 82f116a4 803e6da3 80372ae0 00000577
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.213720] 80543fac 00000000 00000004 82facbc8 00000000 800594cc 8037d094 803e0000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.213720] 00000000 00000000 8037b4a0 82f0f8d4 00000000 800573d0 80546d42 00000072
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.213720] 803e5e50 801bdc00 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.213720] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.213720] ...
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.250228] Call Trace:
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.252758] [<80024f84>] show_stack+0×54/0×88 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.257326] [<80032f00>] warn_slowpath_common+0xa0/0xd0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.262734] [<80032fb8>] warn_slowpath_null+0×18/0×24 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.268204] [<82c262e4>] ieee80211_rx_napi+0×240/0x97c [mac80211]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.274764] [<832c7260>] ath_rx_tasklet+0xc24/0xc88 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.280582] [<832c733c>] ath_stoprecv+0×78/0xf34 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.286105] [<832c3230>] ath9k_deinit_device+0x6d0/0×944 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.292342] [<832c503c>] ath9k_calculate_summary_state+0×500/0×600 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.299491]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.300968] —[ end trace 0902623f520cb0d1 ]— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.306459] ————[ cut here ]———— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.311521] WARNING: CPU: 0 PID: 1399 at backports-2017-10-06/net/mac80211/rx.c:629 ieee80211_rx_napi+0×240/0x97c [mac80211]()
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.323280] Modules linked in: ath9k ath9k_htc ath9k_common pppoe ppp_async option cdc_mbim ath9k_hw ath usb_wwan rndis_host qmi_wwan pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE huawei_cdc_ncm cfg80211 cdc_subset cdc_ncm cdc_ether cdc_eem xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state xt_recent xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_cTue Oct 24 13:08:04 2017 kern.warn kernel: [19935.466515] CPU: 0 PID: 1399 Comm: wpa_supplicant Tainted: G W 4.4.93 #0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.474607] Stack : 80546d42 00000049 00000000 803f0000 82f116a4 803e6da3 80372ae0 00000577
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.474607] 80543fac 00000000 00000004 82e5fc78 00000000 800594cc 8037d094 803e0000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.474607] 00000000 00000000 8037b4a0 82f0f8d4 00000000 800573d0 80546d42 00000072
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.474607] 803e5e50 801bdc00 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.474607] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.474607] ...
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.511109] Call Trace:
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.513687] [<80024f84>] show_stack+0×54/0×88 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.518223] [<80032f00>] warn_slowpath_common+0xa0/0xd0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.523627] [<80032fb8>] warn_slowpath_null+0×18/0×24 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.529085] [<82c262e4>] ieee80211_rx_napi+0×240/0x97c [mac80211]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.535639] [<832c7260>] ath_rx_tasklet+0xc24/0xc88 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.541450] [<832c733c>] ath_stoprecv+0×78/0xf34 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.546964] [<832c3230>] ath9k_deinit_device+0x6d0/0×944 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.553203] [<832c503c>] ath9k_calculate_summary_state+0×500/0×600 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.560352]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.561886] —[ end trace 0902623f520cb0d2 ]— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.566864] ————[ cut here ]———— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.571907] WARNING: CPU: 0 PID: 1399 at backports-2017-10-06/net/mac80211/rx.c:629 ieee80211_rx_napi+0×240/0x97c [mac80211]()
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.583683] Modules linked in: ath9k ath9k_htc ath9k_common pppoe ppp_async option cdc_mbim ath9k_hw ath usb_wwan rndis_host qmi_wwan pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE huawei_cdc_ncm cfg80211 cdc_subset cdc_ncm cdc_ether cdc_eem xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state xt_recent xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_cTue Oct 24 13:08:04 2017 kern.warn kernel: [19935.726919] CPU: 0 PID: 1399 Comm: wpa_supplicant Tainted: G W 4.4.93 #0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.735002] Stack : 80546d42 00000049 00000000 803f0000 82f116a4 803e6da3 80372ae0 00000577
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.735002] 80543fac 00000000 00000004 81cb0438 00000000 800594cc 8037d094 803e0000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.735002] 00000000 00000000 8037b4a0 82f0f8d4 00000000 800573d0 80546d42 00000072
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.735002] 803e5e50 801bdc00 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.735002] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.735002] ...
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.771513] Call Trace:
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.774086] [<80024f84>] show_stack+0×54/0×88 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.778616] [<80032f00>] warn_slowpath_common+0xa0/0xd0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.784025] [<80032fb8>] warn_slowpath_null+0×18/0×24 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.789498] [<82c262e4>] ieee80211_rx_napi+0×240/0x97c [mac80211]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.796088] [<832c7260>] ath_rx_tasklet+0xc24/0xc88 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.801901] [<832c733c>] ath_stoprecv+0×78/0xf34 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.807424] [<832c3230>] ath9k_deinit_device+0x6d0/0×944 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.813664] [<832c503c>] ath9k_calculate_summary_state+0×500/0×600 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.820820]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.822353] —[ end trace 0902623f520cb0d3 ]— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.827454] ————[ cut here ]———— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.832505] WARNING: CPU: 0 PID: 1399 at backports-2017-10-06/net/mac80211/rx.c:629 ieee80211_rx_napi+0×240/0x97c [mac80211]()
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.844268] Modules linked in: ath9k ath9k_htc ath9k_common pppoe ppp_async option cdc_mbim ath9k_hw ath usb_wwan rndis_host qmi_wwan pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE huawei_cdc_ncm cfg80211 cdc_subset cdc_ncm cdc_ether cdc_eem xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state xt_recent xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_cTue Oct 24 13:08:04 2017 kern.warn kernel: [19935.987502] CPU: 0 PID: 1399 Comm: wpa_supplicant Tainted: G W 4.4.93 #0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.995596] Stack : 80546d42 00000049 00000000 803f0000 82f116a4 803e6da3 80372ae0 00000577
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.995596] 80543fac 00000000 00000004 82ea0388 00000000 800594cc 8037d094 803e0000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.995596] 00000000 00000000 8037b4a0 82f0f8d4 00000000 800573d0 80546d42 00000072
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.995596] 803e5e50 801bdc00 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.995596] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19935.995596] ...
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.032096] Call Trace:
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.034672] [<80024f84>] show_stack+0×54/0×88 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.039202] [<80032f00>] warn_slowpath_common+0xa0/0xd0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.044605] [<80032fb8>] warn_slowpath_null+0×18/0×24 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.050060] [<82c262e4>] ieee80211_rx_napi+0×240/0x97c [mac80211]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.056609] [<832c7260>] ath_rx_tasklet+0xc24/0xc88 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.062421] [<832c733c>] ath_stoprecv+0×78/0xf34 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.067946] [<832c3230>] ath9k_deinit_device+0x6d0/0×944 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.074183] [<832c503c>] ath9k_calculate_summary_state+0×500/0×600 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.081379]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.082854] —[ end trace 0902623f520cb0d4 ]— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.088001] ————[ cut here ]———— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.093055] WARNING: CPU: 0 PID: 1399 at backports-2017-10-06/net/mac80211/rx.c:629 ieee80211_rx_napi+0×240/0x97c [mac80211]()
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.104833] Modules linked in: ath9k ath9k_htc ath9k_common pppoe ppp_async option cdc_mbim ath9k_hw ath usb_wwan rndis_host qmi_wwan pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE huawei_cdc_ncm cfg80211 cdc_subset cdc_ncm cdc_ether cdc_eem xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state xt_recent xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_cTue Oct 24 13:08:04 2017 kern.warn kernel: [19936.248068] CPU: 0 PID: 1399 Comm: wpa_supplicant Tainted: G W 4.4.93 #0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.256152] Stack : 80546d42 00000049 00000000 803f0000 82f116a4 803e6da3 80372ae0 00000577
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.256152] 80543fac 00000000 00000004 81f19178 00000000 800594cc 8037d094 803e0000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.256152] 00000000 00000000 8037b4a0 82f0f8d4 00000000 800573d0 80546d42 00000072
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.256152] 803e5e50 801bdc00 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.256152] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.256152] ...
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.292662] Call Trace:
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.295236] [<80024f84>] show_stack+0×54/0×88 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.299769] [<80032f00>] warn_slowpath_common+0xa0/0xd0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.305173] [<80032fb8>] warn_slowpath_null+0×18/0×24 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.310640] [<82c262e4>] ieee80211_rx_napi+0×240/0x97c [mac80211]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.317193] [<832c7260>] ath_rx_tasklet+0xc24/0xc88 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.323006] [<832c733c>] ath_stoprecv+0×78/0xf34 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.328528] [<832c3230>] ath9k_deinit_device+0x6d0/0×944 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.334767] [<832c503c>] ath9k_calculate_summary_state+0×500/0×600 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.341917]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.343392] —[ end trace 0902623f520cb0d5 ]— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.348255] ————[ cut here ]———— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.353264] WARNING: CPU: 0 PID: 1399 at backports-2017-10-06/net/mac80211/rx.c:629 ieee80211_rx_napi+0×240/0x97c [mac80211]()
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.365024] Modules linked in: ath9k ath9k_htc ath9k_common pppoe ppp_async option cdc_mbim ath9k_hw ath usb_wwan rndis_host qmi_wwan pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE huawei_cdc_ncm cfg80211 cdc_subset cdc_ncm cdc_ether cdc_eem xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state xt_recent xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_cTue Oct 24 13:08:04 2017 kern.warn kernel: [19936.508257] CPU: 0 PID: 1399 Comm: wpa_supplicant Tainted: G W 4.4.93 #0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.516351] Stack : 80546d42 00000049 00000000 803f0000 82f116a4 803e6da3 80372ae0 00000577
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.516351] 80543fac 00000000 00000004 81f19388 00000000 800594cc 8037d094 803e0000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.516351] 00000000 00000000 8037b4a0 82f0f8d4 00000000 800573d0 80546d42 00000072
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.516351] 803e5e50 801bdc00 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.516351] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.516351] ...
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.552851] Call Trace:
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.555426] [<80024f84>] show_stack+0×54/0×88 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.559954] [<80032f00>] warn_slowpath_common+0xa0/0xd0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.565385] [<80032fb8>] warn_slowpath_null+0×18/0×24 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.570846] [<82c262e4>] ieee80211_rx_napi+0×240/0x97c [mac80211]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.577439] [<832c7260>] ath_rx_tasklet+0xc24/0xc88 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.583234] [<832c733c>] ath_stoprecv+0×78/0xf34 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.588753] [<832c3230>] ath9k_deinit_device+0x6d0/0×944 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.594994] [<832c503c>] ath9k_calculate_summary_state+0×500/0×600 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.602141]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.603617] —[ end trace 0902623f520cb0d6 ]— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.608659] ————[ cut here ]———— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.613702] WARNING: CPU: 0 PID: 1399 at backports-2017-10-06/net/mac80211/rx.c:629 ieee80211_rx_napi+0×240/0x97c [mac80211]()
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.625478] Modules linked in: ath9k ath9k_htc ath9k_common pppoe ppp_async option cdc_mbim ath9k_hw ath usb_wwan rndis_host qmi_wwan pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE huawei_cdc_ncm cfg80211 cdc_subset cdc_ncm cdc_ether cdc_eem xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state xt_recent xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_cTue Oct 24 13:08:04 2017 kern.warn kernel: [19936.768715] CPU: 0 PID: 1399 Comm: wpa_supplicant Tainted: G W 4.4.93 #0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.776800] Stack : 80546d42 00000049 00000000 803f0000 82f116a4 803e6da3 80372ae0 00000577
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.776800] 80543fac 00000000 00000004 82ea09b8 00000000 800594cc 8037d094 803e0000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.776800] 00000000 00000000 8037b4a0 82f0f8d4 00000000 800573d0 80546d42 00000072
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.776800] 803e5e50 801bdc00 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.776800] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.776800] ...
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.813310] Call Trace:
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.815844] [<80024f84>] show_stack+0×54/0×88 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.820406] [<80032f00>] warn_slowpath_common+0xa0/0xd0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.825814] [<80032fb8>] warn_slowpath_null+0×18/0×24 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.831286] [<82c262e4>] ieee80211_rx_napi+0×240/0x97c [mac80211]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.837839] [<832c7260>] ath_rx_tasklet+0xc24/0xc88 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.843652] [<832c733c>] ath_stoprecv+0×78/0xf34 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.849166] [<832c3230>] ath9k_deinit_device+0x6d0/0×944 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.855406] [<832c503c>] ath9k_calculate_summary_state+0×500/0×600 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.862554]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.864030] —[ end trace 0902623f520cb0d7 ]— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.869073] ————[ cut here ]———— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.874115] WARNING: CPU: 0 PID: 1399 at backports-2017-10-06/net/mac80211/rx.c:629 ieee80211_rx_napi+0×240/0x97c [mac80211]()
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19936.885876] Modules linked in: ath9k ath9k_htc ath9k_common pppoe ppp_async option cdc_mbim ath9k_hw ath usb_wwan rndis_host qmi_wwan pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE huawei_cdc_ncm cfg80211 cdc_subset cdc_ncm cdc_ether cdc_eem xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state xt_recent xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_cTue Oct 24 13:08:04 2017 kern.warn kernel: [19937.029111] CPU: 0 PID: 1399 Comm: wpa_supplicant Tainted: G W 4.4.93 #0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.037203] Stack : 80546d42 00000049 00000000 803f0000 82f116a4 803e6da3 80372ae0 00000577
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.037203] 80543fac 00000000 00000004 81f19908 00000000 800594cc 8037d094 803e0000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.037203] 00000000 00000000 8037b4a0 82f0f8d4 00000000 800573d0 80546d42 00000072
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.037203] 803e5e50 801bdc00 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.037203] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.037203] ...
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.073706] Call Trace:
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.076235] [<80024f84>] show_stack+0×54/0×88 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.080803] [<80032f00>] warn_slowpath_common+0xa0/0xd0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.086208] [<80032fb8>] warn_slowpath_null+0×18/0×24 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.091662] [<82c262e4>] ieee80211_rx_napi+0×240/0x97c [mac80211]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.098218] [<832c7260>] ath_rx_tasklet+0xc24/0xc88 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.104028] [<832c733c>] ath_stoprecv+0×78/0xf34 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.109546] [<832c3230>] ath9k_deinit_device+0x6d0/0×944 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.115783] [<832c503c>] ath9k_calculate_summary_state+0×500/0×600 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.122932]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.124408] —[ end trace 0902623f520cb0d8 ]— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.129917] ————[ cut here ]———— Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.134978] WARNING: CPU: 0 PID: 1399 at backports-2017-10-06/net/mac80211/rx.c:629 ieee80211_rx_napi+0×240/0x97c [mac80211]()
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.146753] Modules linked in: ath9k ath9k_htc ath9k_common pppoe ppp_async option cdc_mbim ath9k_hw ath usb_wwan rndis_host qmi_wwan pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE huawei_cdc_ncm cfg80211 cdc_subset cdc_ncm cdc_ether cdc_eem xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state xt_recent xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_cTue Oct 24 13:08:04 2017 kern.warn kernel: [19937.289992] CPU: 0 PID: 1399 Comm: wpa_supplicant Tainted: G W 4.4.93 #0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.298075] Stack : 80546d42 00000049 00000000 803f0000 82f116a4 803e6da3 80372ae0 00000577
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.298075] 80543fac 00000000 00000004 82e2f858 00000000 800594cc 8037d094 803e0000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.298075] 00000000 00000000 8037b4a0 82f0f8d4 00000000 800573d0 80546d42 00000072
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.298075] 803e5e50 801bdc00 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.298075] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.298075] ...
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.334586] Call Trace:
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.337114] [<80024f84>] show_stack+0×54/0×88 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.341682] [<80032f00>] warn_slowpath_common+0xa0/0xd0
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.347086] [<80032fb8>] warn_slowpath_null+0×18/0×24 Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.352552] [<82c262e4>] ieee80211_rx_napi+0×240/0x97c [mac80211]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.359107] [<832c7260>] ath_rx_tasklet+0xc24/0xc88 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.364916] [<832c733c>] ath_stoprecv+0×78/0xf34 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.370434] [<832c3230>] ath9k_deinit_device+0x6d0/0×944 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.376670] [<832c503c>] ath9k_calculate_summary_state+0×500/0×600 [ath9k]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.383819]
Tue Oct 24 13:08:04 2017 kern.warn kernel: [19937.385297] —[ end trace 0902623f520cb0d9 ]— Tue Oct 24 13:08:04 2017 daemon.info odhcpd[914]: Using a RA lifetime of 0 seconds on br-lan
Tue Oct 24 13:08:04 2017 daemon.notice hostapd: nl80211: nl80211_recv_beacons→nl_recvmsgs failed: -5
Tue Oct 24 13:10:24 2017 daemon.info hostapd: wlan0-1: STA f0:25:b7:b2:fe:ea IEEE 802.11: authenticated
Tue Oct 24 13:10:24 2017 daemon.info hostapd: wlan0-1: STA f0:25:b7:b2:fe:ea IEEE 802.11: associated (aid 1)
Tue Oct 24 13:10:24 2017 daemon.notice hostapd: wlan0-1: AP-STA-CONNECTED f0:25:b7:b2:fe:ea
Tue Oct 24 13:10:24 2017 daemon.info hostapd: wlan0-1: STA f0:25:b7:b2:fe:ea RADIUS: starting accounting session 747735F6C298AD3B
Tue Oct 24 13:10:24 2017 daemon.info hostapd: wlan0-1: STA f0:25:b7:b2:fe:ea WPA: pairwise key handshake completed (RSN)
Tue Oct 24 13:10:24 2017 daemon.info dnsmasq-dhcp[2988]: DHCPDISCOVER(br-lan) f0:25:b7:b2:fe:ea

 


15.06.2017848Base systemBug ReportVery LowLowWiFi LED won't turn off on TP-Link TL-WDR3600 v1lede-17.01Unconfirmed Task Description

- Device problem occurs on

TP-Link TL-WDR3600 v1

- Software versions of LEDE release, packages, etc.

LEDE Reboot 17.01.2 r3435-65eec8bd5f / LuCI lede-17.01 branch (git-17.152.82987-7f6fc16)

- Steps to reproduce

Switch LED “trigger” to “none” on “ath9k-phy0”, LED will continue to blink.
Strangely it will work fine for “ath9k-phy1”.

16.11.20171172Base systemBug ReportVery LowLowWifi keeps on scanning even if all the clients network ...TrunkUnconfirmed Task Description

Occurs on a WRT3200ACM using trunk and latest mwl driver.
Problem initially reported here: https://github.com/kaloz/mwlwifi/issues/231 , not a driver issue according to the developer.

With the latest commit and firmware (or last “stable”) I get a continuous flow of these when 2g is disabled but set-up in client mode:

Wed Nov 15 12:43:51 2017 kern.debug kernel: [   57.131906] ieee80211 phy1: change: 0x40
Wed Nov 15 12:43:52 2017 kern.debug kernel: [   57.281823] ieee80211 phy1: change: 0x40
Wed Nov 15 12:43:52 2017 kern.debug kernel: [   57.451823] ieee80211 phy1: change: 0x40
Wed Nov 15 12:43:52 2017 kern.debug kernel: [   57.601818] ieee80211 phy1: change: 0x40
Wed Nov 15 12:43:52 2017 kern.debug kernel: [   57.761816] ieee80211 phy1: change: 0x40
Wed Nov 15 12:43:52 2017 kern.debug kernel: [   57.911826] ieee80211 phy1: change: 0x40
Wed Nov 15 12:43:52 2017 kern.debug kernel: [   58.071827] ieee80211 phy1: change: 0x40
Wed Nov 15 12:43:53 2017 kern.debug kernel: [   58.221822] ieee80211 phy1: change: 0x40
Wed Nov 15 12:43:53 2017 kern.debug kernel: [   58.381808] ieee80211 phy1: change: 0x40
Wed Nov 15 12:43:53 2017 kern.debug kernel: [   58.531807] ieee80211 phy1: change: 0x40
Wed Nov 15 12:43:53 2017 kern.debug kernel: [   58.691811] ieee80211 phy1: change: 0x40
Wed Nov 15 12:43:53 2017 kern.debug kernel: [   58.841815] ieee80211 phy1: change: 0x40
Wed Nov 15 12:43:53 2017 kern.debug kernel: [   59.011806] ieee80211 phy1: change: 0x40
Wed Nov 15 12:43:53 2017 kern.debug kernel: [   59.161804] ieee80211 phy1: change: 0x40
Wed Nov 15 12:43:54 2017 kern.debug kernel: [   59.238814] ieee80211 phy1: change: 0x100
Wed Nov 15 12:43:54 2017 kern.debug kernel: [   60.163807] ieee80211 phy1: change: 0x100

mwlwifi main developer says it just indicates that the interface is continuously scanning.
The only way to stop it was to delete the client network on this interface, disabling it was not enough.

05.02.2017469Base systemBug ReportVery LowLowWifi firmware file is not available on ZyXEL P-2812HNU-...lede-17.01Unconfirmed Task Description

Kernel log:

[   11.336056] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[   11.340485] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'RT3062.eeprom'.
[   11.350276] rt2800pci 0000:00:0e.0: Direct firmware load for RT3062.eeprom failed with error -2
[   11.358782] rt2800pci 0000:00:0e.0: Falling back to user helper
[   11.479331] firmware RT3062.eeprom: firmware_loading_store: map pages failed
[   11.485217] ieee80211 phy0: rt2x00lib_request_eeprom_file: Error - Failed to request EEPROM.
[   11.493519] rt2800pci: probe of 0000:00:0e.0 failed with error -11

Firmware files:

root@lede:/lib/firmware# ls /lib/firmware/
lantiq-vrx200-a-to-b.bspatch                 rt2860.bin                                   xcpe_581816_580B11.LICENSE                   xcpe_581816_580B11_to_579906_574402.bspatch
lantiq-vrx200-a.bin                          rt3290.bin                                   xcpe_581816_580B11.bin

After adding a RT3062.eeprom the wifi port is available.

 


11.02.2017499Base systemBug ReportVery LowLowWiFi client mode leaves router inaccessible if upstream...TrunkUnconfirmed Task Description

This bug was originally reported to the OpenWrt team and there is a discussion of it in their mailing list. Luiz Angelo Daros de Luca suggested reporting here (and switching to LEDE, which I will do).

I have a TP-Link TL-MR3020 v1.9 with Chaos Calmer 15.05.01. I’m using it to provide a WiFi access point to my phone/tablet while I travel, and it’s acting as a WiFi client for the various hostels I visit.

If you configure it as a wifi client with a wwan interface using the LuCI scan/join wizard, and then you configure a wifi access point on the same radio, the router works as expected and when you connect to the router’s AP, you get Internet via the client connection.

However, if you move out of range of the network the router is a client of, or if it goes down, when you power off the OpenWrt router and power back on, the access point won’t come up.

The AP will only come up if the client network you configured is also working; so you have no way to connect to the router over wifi, and no way to reconfigure the router, if that client network is down or out of range.

This is a particular problem for a travel router because it will often move it out of range of the original upstream network, and you may only have a wifi-capable device with which to reconfigure it.

The Ethernet port on the router does remain active, so I can tell it does actually boot. It’s just the radio that doesn’t come up. I managed to get back in range of a network once, and the router worked as expected.

It doesn’t matter whether the AP or client connection are configured first or second on the radio interface, and, unticking “bring up on boot” for the wwan interface has no effect on the behaviour.

Steps to reproduce: Connect the router to a wifi network as a client using the Join wizard. Add a wifi master-mode access point on the same radio interface. Verify you can access the Internet by joining the router’s new master AP. Reboot the router with the original network it was a client of turned off. Notice the router’s AP you configured never comes up.

Expected behaviour: The master access point of the router should always come up, regardless of the availability of the client network.

The OpenWRT team will not fix it, but had some explanation as to why it is happening. IMO, it’s still a very frustrating bug and most users would expect the behaviour I did.

19.10.20171079KernelBug ReportVery LowCriticalWifi 5GHz & Kernel 4.4 vs 4.9 [Netgear R8000/bcm53xx]AllUnconfirmed Task Description

Tested on Netgear R8000/bcm53xx
LEDE Reboot SNAPSHOT r5099-5fff2f4 / LuCI Master (git-17.289.64212-462779c)

Since Kernel 4.9, the Wifi 5GHz (radio 0 and radio 2) does not work: visible, but unable to connect or disconnected after few seconds (unable to receive IP at all).

Today, I tested to compile the build but with the previous kernel 4.4, all Wifi 5GHz work.

The LEDE config (on the device) are strictly identical between both tests.

Attached all files about both build.

27.05.2017814Base systemBug ReportVery LowLowWhen LEDE is compiled with GCC 7 on at least ar71xx and...TrunkAssigned Task Description

When using the GCC 7.x compiler, I have found that Dropbear in LEDE images for ar71xx (Ubiquiti Unifi) and brcm47xx (generic) (built with the default configuration, other than changing the compiler to GCC 7.x) won’t accept incoming SSH connections. Instead, as soon as a connection is received, it spins the CPU indefinitely and the connecting SSH client hangs. Nothing relevant is printed in the logs. This behavior does not occur on x86_64; there Dropbear works fine.

I realize I haven’t provided much information here, but I don’t really know how to collect anything else on embedded platforms like this. One of the devices on which I have reproduced this does have a serial adapter though, so I can use that to get any additional information that might be helpful.

21.03.2017649Base systemBug ReportVery LowLowWDS not working on ath9k-htc TrunkUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on: Any device with an wifi USB adapter with the chipset AR9271 (TPLink WN722N in my case).
- Software versions of LEDE release, packages, etc: Latest trunk LEDE versions.
- Steps to reproduce

 

Configure the USB AR9271 adapter as WDS AP, try to associate any other router as WDS Client (in my case the WDS Client is a TPLink WR741ND router, also compiled with latest trunk).
They both associate correctly, but there is no connection between them.

Here is a hostapd log on the WDS AP:

Mon Mar 20 14:05:00 2017 daemon.notice hostapd: wlan1: interface state ENABLED->DISABLED
Mon Mar 20 14:05:00 2017 daemon.notice hostapd: wlan1: AP-STA-DISCONNECTED 94:0c:6d:b0:f4:ac
Mon Mar 20 14:05:00 2017 daemon.notice hostapd: wlan1: AP-DISABLED
Mon Mar 20 14:05:00 2017 daemon.notice hostapd: wlan1: CTRL-EVENT-TERMINATING
Mon Mar 20 14:05:00 2017 daemon.notice hostapd: nl80211: deinit ifname=wlan1 disabled_11b_rates=0
Mon Mar 20 14:05:01 2017 daemon.err hostapd: Configuration file: /var/run/hostapd-phy1.conf
Mon Mar 20 14:05:02 2017 daemon.notice hostapd: wlan1: interface state UNINITIALIZED->COUNTRY_UPDATE
Mon Mar 20 14:05:02 2017 daemon.err hostapd: Using interface wlan1 with hwaddr e8:de:27:a4:58:21 and ssid "EB1DJ"
Mon Mar 20 14:05:02 2017 daemon.notice hostapd: wlan1: interface state COUNTRY_UPDATE->ENABLED
Mon Mar 20 14:05:02 2017 daemon.notice hostapd: wlan1: AP-ENABLED
Mon Mar 20 14:05:03 2017 daemon.debug hostapd: wlan1: STA 94:0c:6d:b0:f4:ac IEEE 802.11: authentication OK (open system)
Mon Mar 20 14:05:03 2017 daemon.debug hostapd: wlan1: STA 94:0c:6d:b0:f4:ac MLME: MLME-AUTHENTICATE.indication(94:0c:6d:b0:f4:ac, OPEN_SYSTEM)
Mon Mar 20 14:05:03 2017 daemon.debug hostapd: wlan1: STA 94:0c:6d:b0:f4:ac MLME: MLME-DELETEKEYS.request(94:0c:6d:b0:f4:ac)
Mon Mar 20 14:05:03 2017 daemon.info hostapd: wlan1: STA 94:0c:6d:b0:f4:ac IEEE 802.11: authenticated
Mon Mar 20 14:05:03 2017 daemon.debug hostapd: wlan1: STA 94:0c:6d:b0:f4:ac IEEE 802.11: association OK (aid 1)
Mon Mar 20 14:05:03 2017 daemon.info hostapd: wlan1: STA 94:0c:6d:b0:f4:ac IEEE 802.11: associated (aid 1)
Mon Mar 20 14:05:03 2017 daemon.debug hostapd: wlan1: STA 94:0c:6d:b0:f4:ac MLME: MLME-ASSOCIATE.indication(94:0c:6d:b0:f4:ac)
Mon Mar 20 14:05:03 2017 daemon.debug hostapd: wlan1: STA 94:0c:6d:b0:f4:ac MLME: MLME-DELETEKEYS.request(94:0c:6d:b0:f4:ac)
Mon Mar 20 14:05:03 2017 daemon.debug hostapd: wlan1: STA 94:0c:6d:b0:f4:ac IEEE 802.11: binding station to interface 'wlan1'
Mon Mar 20 14:05:03 2017 daemon.debug hostapd: wlan1: STA 94:0c:6d:b0:f4:ac WPA: event 1 notification
Mon Mar 20 14:05:03 2017 daemon.debug hostapd: wlan1: STA 94:0c:6d:b0:f4:ac WPA: start authentication
Mon Mar 20 14:05:03 2017 daemon.debug hostapd: wlan1: STA 94:0c:6d:b0:f4:ac IEEE 802.1X: unauthorizing port
Mon Mar 20 14:05:03 2017 daemon.debug hostapd: wlan1: STA 94:0c:6d:b0:f4:ac WPA: sending 1/4 msg of 4-Way Handshake
Mon Mar 20 14:05:03 2017 daemon.debug hostapd: wlan1: STA 94:0c:6d:b0:f4:ac WPA: EAPOL-Key timeout
Mon Mar 20 14:05:03 2017 daemon.debug hostapd: wlan1: STA 94:0c:6d:b0:f4:ac WPA: sending 1/4 msg of 4-Way Handshake
Mon Mar 20 14:05:03 2017 daemon.debug hostapd: wlan1: STA 94:0c:6d:b0:f4:ac WPA: received EAPOL-Key frame (2/4 Pairwise)
Mon Mar 20 14:05:03 2017 daemon.debug hostapd: wlan1: STA 94:0c:6d:b0:f4:ac WPA: sending 3/4 msg of 4-Way Handshake
Mon Mar 20 14:05:03 2017 daemon.err hostapd: nl80211: EAPOL TX: No message of desired type
Mon Mar 20 14:05:03 2017 daemon.debug hostapd: wlan1: STA 94:0c:6d:b0:f4:ac WPA: ignore retransmitted EAPOL-Key 2/4 Pairwise - SNonce did not change
Mon Mar 20 14:05:03 2017 daemon.debug hostapd: wlan1: STA 94:0c:6d:b0:f4:ac WPA: EAPOL-Key timeout
Mon Mar 20 14:05:03 2017 daemon.debug hostapd: wlan1: STA 94:0c:6d:b0:f4:ac WPA: sending 3/4 msg of 4-Way Handshake
Mon Mar 20 14:05:03 2017 daemon.debug hostapd: wlan1: STA 94:0c:6d:b0:f4:ac WPA: received EAPOL-Key frame (4/4 Pairwise)
Mon Mar 20 14:05:03 2017 daemon.notice hostapd: wlan1: AP-STA-CONNECTED 94:0c:6d:b0:f4:ac
Mon Mar 20 14:05:03 2017 daemon.debug hostapd: wlan1: STA 94:0c:6d:b0:f4:ac IEEE 802.1X: authorizing port
Mon Mar 20 14:05:03 2017 daemon.info hostapd: wlan1: STA 94:0c:6d:b0:f4:ac RADIUS: starting accounting session 7797AE68AEE646F3
Mon Mar 20 14:05:03 2017 daemon.info hostapd: wlan1: STA 94:0c:6d:b0:f4:ac WPA: pairwise key handshake completed (RSN)
Tue Mar 21 09:58:59 2017 daemon.debug hostapd: wlan1: STA 94:0c:6d:b0:f4:ac IEEE 802.11: authentication OK (open system)
Tue Mar 21 09:58:59 2017 daemon.debug hostapd: wlan1: STA 94:0c:6d:b0:f4:ac WPA: event 0 notification
Tue Mar 21 09:58:59 2017 daemon.debug hostapd: wlan1: STA 94:0c:6d:b0:f4:ac MLME: MLME-AUTHENTICATE.indication(94:0c:6d:b0:f4:ac, OPEN_SYSTEM)
Tue Mar 21 09:58:59 2017 daemon.debug hostapd: wlan1: STA 94:0c:6d:b0:f4:ac MLME: MLME-DELETEKEYS.request(94:0c:6d:b0:f4:ac)
Tue Mar 21 09:58:59 2017 daemon.info hostapd: wlan1: STA 94:0c:6d:b0:f4:ac IEEE 802.11: authenticated
Tue Mar 21 09:58:59 2017 daemon.debug hostapd: wlan1: STA 94:0c:6d:b0:f4:ac IEEE 802.11: association OK (aid 1)
Tue Mar 21 09:58:59 2017 daemon.info hostapd: wlan1: STA 94:0c:6d:b0:f4:ac IEEE 802.11: associated (aid 1)

I think the error Mon Mar 20 14:05:03 2017 daemon.err hostapd: nl80211: EAPOL TX: No message of desired type has something to do with WDS not working?.

If there is any other info, tests etc you require feel free to ask.

08.03.2017608Base systemBug ReportVery LowHighwds AP/STA disconnecting every 10 minutesTrunkUnconfirmed Task Description

Devices:
AP WDS: Netgear r7800
STA WDS: TP-LINK Archer c7 v2

Problem exists on:

  1. with both latest trunk and 17.01
  2. with both ath10k and ath10k-ct
  3. with STP enabled or not on both sides
  4. with STP enabled or not on only one side
  5. with both WPA2 tkip and aes
  6. with 2.4Ghz and 5Ghz bands

Steps to reproduce

  1. Configure AP WDS
  2. Configure STA WDS
  3. Wait exactly 10 minutes and you’ll see this in the log:

AP:

daemon.info hostapd: wlan1-1: STA 30:b5:c2:08:b9:e1 IEEE 802.11: authenticated
daemon.info hostapd: wlan1-1: STA 30:b5:c2:08:b9:e1 IEEE 802.11: associated (aid 1)
daemon.info hostapd: wlan1-1: STA 30:b5:c2:08:b9:e1 RADIUS: starting accounting session F72C76B14648E205
daemon.info hostapd: wlan1-1: STA 30:b5:c2:08:b9:e1 WPA: pairwise key handshake completed (RSN)

STA:

daemon.notice netifd: Network device 'wlan1' link is down
kern.info kernel: [  387.179978] wlan1: deauthenticated from de:ef:09:f2:99:75 (Reason: 2=PREV_AUTH_NOT_VALID)
kern.info kernel: [  387.188344] br-lan: port 3(wlan1) entered disabled state
kern.info kernel: [  388.139233] wlan1: authenticate with de:ef:09:f2:99:75
kern.info kernel: [  388.170697] wlan1: send auth to de:ef:09:f2:99:75 (try 1/3)
kern.info kernel: [  388.195249] wlan1: authenticated
Wkern.info kernel: [  388.225092] wlan1: associate with de:ef:09:f2:99:75 (try 1/3)
kern.info kernel: [  388.235224] wlan1: RX AssocResp from de:ef:09:f2:99:75 (capab=0x431 status=0 aid=1)
kern.info kernel: [  388.243356] wlan1: associated
daemon.notice netifd: Network device 'wlan1' link is up

I think this has to do with wpa_supplicant in some way, maybe it doesn’t receive the correct packets and force disconnect the client?

Now, this only happens in WDS bridge mode. I’m currently using relayd in order to overcome this issue and it works like a charm.
I want to solve this problem since relayd uses much more cpu power (indeed this is a true routing procotol after all) and total troughput is halved right now.


10.03.2017615KernelBug ReportMediumHighWDS AP: kernel panic under high traffic loadTrunkNew Task Description

I built a WDS bridge with two TL-WR841 v8, running LEDE r3670-154b3a6 from the buildbot snapshots.

When sending a high amount of traffic through the bridge (bidirectional iperf from one computer to another through the bridge), the WDS AP crashes repeatedly (roughly every hour, sometimes it takes a bit longer).

This is possibly related to other WDS issues  FS#447  and FS#608.

AP wireless config:

config wifi-iface 'default_radio0'
	option device 'radio0'
	option network 'lan'
	option mode 'ap'
	option ssid 'LEDE'
	option encryption 'psk-mixed'
	option key 'XXX'
	option wds '1'

STA wireless config:

config wifi-iface 'default_radio0'
	option device 'radio0'
	option network 'lan'
	option mode 'sta'
	option ssid 'LEDE'
	option encryption 'psk2'
	option key 'XXX'
	option wds '1'

The network configuration is unchanged on both devices (except changing the LAN IP).

Some kernel crashes I obtained with /sys/kernel/debug/crashlog after a crash:


[ 2581.160504] Trap instruction in kernel code[#1]:
[ 2581.165297] CPU: 0 PID: 0 Comm: swapper Not tainted 4.4.52 #0
[ 2581.171239] task: 8042ef58 ti: 80428000 task.ti: 80428000
[ 2581.176814] $ 0   : 00000000 804a0000 00000000 fffffffe
[ 2581.182253] $ 4   : 00afc0cc 009f844e 0000007f a0e7c980
[ 2581.187691] $ 8   : 009f849c 00000052 0000004a 01000000
[ 2581.193129] $12   : 80000000 8000004e 00000000 00000002
[ 2581.198559] $16   : 81b27000 80df7000 81a15000 81942f00
[ 2581.203989] $20   : 00000000 00000000 8042a4e0 80d18400
[ 2581.209428] $24   : 00000000 8007d2d4
[ 2581.214866] $28   : 80428000 81809a58 8042a4e0 80272104
[ 2581.220305] Hi    : 00000019
[ 2581.223280] Lo    : 00000000
[ 2581.226272] epc   : 80272128 __dev_queue_xmit+0x2d8/0x4c4
[ 2581.231852] ra    : 80272104 __dev_queue_xmit+0x2b4/0x4c4
[ 2581.237428] Status: 1100f403 KERNEL EXL IE
[ 2581.241785] Cause : 00800034 (ExcCode 0d)
[ 2581.245924] PrId  : 0001974c (MIPS 74Kc)
[ 2581.249972] Modules linked in: ath9k ath9k_common pppoe ppp_async ath9k_hw ath pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT
ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_CT slhc
nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_conntrack_ipv4 nf_nat_ipv4 nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache
nf_conntrack iptable_mangle iptable_filter ip_tables crc_ccitt compat ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter
ip6_tables x_tables gpio_button_hotplug
[ 2581.309535] Process swapper (pid: 0, threadinfo=80428000, task=8042ef58, tls=00000000)
[ 2581.317710] Stack : 80ecf420 8187992c 81809b2c 81879900 81b27068 00000001 80430000 fffffff4
[ 2581.317710]    80ece09c 80ed7000 0000004a 80ed7000 80d18400 80ed7000 00000000 8035b5a4
[ 2581.317710]    00000000 80df7000 00000000 80905e00 80f81000 80430000 80df7000 80271cd0
[ 2581.317710]    80428000 00440002 00000020 0000000e 00000003 80df7000 8042a4e0 00000000
[ 2581.317710]    80d18400 80271718 80430000 803fc6cc 8190af00 80ece090 80430000 80df7000
[ 2581.317710]    ...
[ 2581.354706] Call Trace:
[ 2581.357239] [] __dev_queue_xmit+0x2d8/0x4c4
[ 2581.362495] [] vlan_dev_hard_start_xmit+0x98/0x128
[ 2581.368341] [] dev_hard_start_xmit+0x2a8/0x354
[ 2581.373834] [] __dev_queue_xmit+0x3c0/0x4c4
[ 2581.379068] [] br_dev_queue_push_xmit+0x16c/0x1a0
[ 2581.384828] [] br_forward_finish+0x3c/0xb0
[ 2581.389963] [] __br_forward+0xa8/0x114
[ 2581.394741] [] br_handle_frame_finish+0x4f4/0x550
[ 2581.400500] [] br_handle_frame+0x380/0x418
[ 2581.405662] [] __netif_receive_skb_core+0x42c/0x898
[ 2581.411768] [] ieee80211_attach_ack_skb+0x103c/0x19e8 [mac80211]
[ 2581.418913]
[ 2581.420454]
[ 2581.420454] Code: 02002025  10000014  00008825  00431024  ae020074  1000000f  00008825  8e020000
[ 2581.430831] ---[ end trace 8251bd1741f30e24 ]---
[ 2581.437731] Kernel panic - not syncing: Fatal exception in interrupt

Another one which is a bit different:

[  420.687915] Reserved instruction in kernel code[#1]:
[  420.693066] CPU: 0 PID: 0 Comm: swapper Not tainted 4.4.52 #0
[  420.699008] task: 8042ef58 ti: 80428000 task.ti: 80428000
[  420.704583] $ 0   : 00000000 804a0000 00000002 00000002
[  420.710022] $ 4   : 81809e34 00000003 00000000 a0fb5980
[  420.715460] $ 8   : 0179f4bc 000005f2 000005ea 01000000
[  420.720898] $12   : 80000000 800005ee 00000000 772a02c0
[  420.726328] $16   : 81809e34 00000000 80f82420 8179eed2
[  420.731758] $20   : 80d54b40 00000000 80f82000 81809ddc
[  420.737197] $24   : 00000000 8007d2d4                  
[  420.742635] $28   : 80428000 81809d28 00000000 80da2a4c
[  420.748066] Hi    : 00000008
[  420.751041] Lo    : 00000023
[  420.754198] epc   : 80da2a4c ieee80211_sta_uapsd_trigger+0xff4/0x2d7c [mac80211]
[  420.761875] ra    : 80da2a4c ieee80211_sta_uapsd_trigger+0xff4/0x2d7c [mac80211]
[  420.769508] Status: 1100f403	KERNEL EXL IE 
[  420.773864] Cause : 80800028 (ExcCode 0a)
[  420.778004] PrId  : 0001974c (MIPS 74Kc)
[  420.782050] Modules linked in: ath9k ath9k_common pppoe ppp_async ath9k_hw ath pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_CT slhc nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_conntrack_ipv4 nf_nat_ipv4 nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack iptable_mangle iptable_filter ip_tables crc_ccitt compat ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables x_tables gpio_button_hotplug
[  420.841606] Process swapper (pid: 0, threadinfo=80428000, task=8042ef58, tls=00000000)
[  420.849779] Stack : 8086da00 8034a074 00000141 81809e14 00000042 81a18c20 00000003 81a18800
[  420.849779] 	  804c0000 00000000 0000002f 00000080 803c9c94 80dd6e74 80de0000 80dd6e40
[  420.849779] 	  80df9780 80440000 80f81420 8034a304 00000032 81b90010 00000001 00000008
[  420.849779] 	  80fc1380 81809e34 80fa9cc0 000008c9 8086f460 00000008 8086f460 00000000
[  420.849779] 	  00000001 80da5abc 815d1746 80df9780 00000000 8034bc5c 00000003 81a18800
[  420.849779] 	  ...
[  420.886779] Call Trace:
[  420.889373] [<80da2a4c>] ieee80211_sta_uapsd_trigger+0xff4/0x2d7c [mac80211]
[  420.896693] 
[  420.898234] 
[  420.898234] Code: 00402825  0c3687a9  02002025 <1000fe1b> 8ee20000  0c36817d  02402025  0441ff8b  24420012 
[  420.908615] ---[ end trace 2fd42b1e71175ff5 ]---
[  420.915438] Kernel panic - not syncing: Fatal exception in interrupt
06.11.20171152Base systemBug ReportVery LowHighWDR3600: Wifi randomly turns off and get disabledlede-17.01Unconfirmed Task Description

Running LEDE 17.01.4

I’m not sure how do I reproduce this problem, it just happen randomly at random time.

This never happened back when I used OpenWRT, were there some regression somewhere?

So with LEDE, my router’s wifi randomly disconnect and disable itself. I have read the logs (provided below) yet I can’t see anything suspicious. I only see these:

Mon Nov  6 13:54:45 2017 daemon.notice procd: /etc/init.d/network: 'radio0' is disabled
Mon Nov  6 13:54:45 2017 daemon.notice procd: /etc/init.d/network: 'radio1' is disabled
Mon Nov  6 13:54:45 2017 daemon.notice procd: /etc/init.d/network: 'radio0' is disabled
Mon Nov  6 13:54:45 2017 daemon.notice procd: /etc/init.d/network: 'radio1' is disabled

This was around the time people in my home messaged me that they cannot find the access point from their devices

It bugs me because I usually go to the office in the afternoon and people in my house complains to me that Wifi stops working without anything being done to the router, I have not set up VPN access to my home network so I cannot do anything until I go home in the evening.

09.03.2017612Base systemBug ReportVery LowHighWAN to LAN leakage on MT7620 devicesTrunkUnconfirmed Task Description

I am currently testing two MT7620 devices - the ZBT WE826 and the Sanlinking D240. During the first seconds of the boot, I see that packets leak between the WAN and LAN ports. Typically, this results in clients receiving a DHCP reply from my upstream router, rendering the clients without connectivity when the switch is properly initialized. I have also tested with the default firmware and do not see this behavior. Also, if I stop the devices in the bootloader, then packets do not leak until I resume boot again.

In order to try to solve this bug, I have tried to port some (at least to me) missing steps from the bootloader switch code and to the mt7620 switch driver in LEDE. This did not have an effect, at least not on the packet leak. A work-around I have found is to update u-boot and remove the input delay, so that the device will boot immediately. However, this is quite cumbersome to install and not very reliable. I suspect my luck with this work-around is more due to the timing of the DHCP clients in Ubuntu and Windows 10.

Does anyone have any idea as to what could be wrong and where to start looking?

Thanks in advance for any help.

 


14.10.2016227Base systemBug ReportMediumHighVLAN support mismatch between preinit and default netwo...TrunkResearching Task Description

PPPoE is broken on WRT1900ACS

Upgraded from Lede r578 to latest Lede r1814 and PPPOE doesn’t work anymore altough the pppd version and PPPoE version are the same:
- Linksys WRT1900ACS
- LEDE reboot r1814

pppd debug log:

Plugin rp-pppoe.so loaded.
RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Send PPPOE Discovery V1T1 PADI session 0×0 length 4
dst ff:ff:ff:ff:ff:ff src c2:56:27:ca:d7:d4
[service-name]
Send PPPOE Discovery V1T1 PADI session 0×0 length 4
dst ff:ff:ff:ff:ff:ff src c2:56:27:ca:d7:d4
[service-name]
Send PPPOE Discovery V1T1 PADI session 0×0 length 4
dst ff:ff:ff:ff:ff:ff src c2:56:27:ca:d7:d4
[service-name]
Timeout waiting for PADO packets
Unable to complete PPPoE Discovery
Plugin rp-pppoe.so loaded.
RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Send PPPOE Discovery V1T1 PADI session 0×0 length 4
dst ff:ff:ff:ff:ff:ff src c2:56:27:ca:d7:d4
[service-name]
Send PPPOE Discovery V1T1 PADI session 0×0 length 4
dst ff:ff:ff:ff:ff:ff src c2:56:27:ca:d7:d4
[service-name]
Send PPPOE Discovery V1T1 PADI session 0×0 length 4
dst ff:ff:ff:ff:ff:ff src c2:56:27:ca:d7:d4
[service-name]

While on the same hardware running LEDE r578, the PPPoE module works as expected:

Plugin rp-pppoe.so loaded.
RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Send PPPOE Discovery V1T1 PADI session 0×0 length 4
dst ff:ff:ff:ff:ff:ff src c2:56:27:ca:d7:d4
[service-name]
Recv PPPOE Discovery V1T1 PADO session 0×0 length 40
dst c2:56:27:ca:d7:d4 src a0:f3:e4:34:d8:21
[service-name] [AC-name acc-aln1.hac] [AC-cookie 75 58 37 a5 ba 3c e4 a5 2a 61 bb 23 92 5c 1b dc]
Send PPPOE Discovery V1T1 PADR session 0×0 length 24
dst a0:f3:e4:34:d8:21 src c2:56:27:ca:d7:d4
[service-name] [AC-cookie 75 58 37 a5 ba 3c e4 a5 2a 61 bb 23 92 5c 1b dc]
Recv PPPOE Discovery V1T1 PADS session 0x30b length 4
dst c2:56:27:ca:d7:d4 src a0:f3:e4:34:d8:21
[service-name]
PADS: Service-Name: ‘’ PPP session is 779
Connected to a0:f3:e4:34:d8:21 via interface eth0
using channel 2
Using interface pppoe-wan
Connect: pppoe-wan ←→ eth0
sent [LCP ConfReq id=0×1 <mru 1492> <magic 0xc6952556>]
rcvd [LCP ConfReq id=0×66 <mru 1492> <auth chap MD5> <magic 0x4cc73648>]
sent [LCP ConfAck id=0×66 <mru 1492> <auth chap MD5> <magic 0x4cc73648>]
rcvd [LCP ConfAck id=0×1 <mru 1492> <magic 0xc6952556>]
sent [LCP EchoReq id=0×0 magic=0xc6952556]
rcvd [CHAP Challenge id=0×1 <7131a44524d1de8f1cd1061cac6d8c071d8bfe7351bc4ea7bd08f56684428475f229ba177a192696ebab32>, name = “acc-aln1.hac”]
sent [CHAP Response id=0×1 <4bb1a418b298790b128ad4d7ef3109ad>, name = “bthomehub@btbroadband.com”]
rcvd [LCP EchoRep id=0×0 magic=0x4cc73648]
rcvd [CHAP Success id=0×1 “CHAP authentication success”]
CHAP authentication succeeded: CHAP authentication success
CHAP authentication succeeded
peer from calling number A0:F3:E4:34:D8:21 authorized
sent [IPCP ConfReq id=0×1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns2 0.0.0.0>]
sent [IPV6CP ConfReq id=0×1 <addr fe80::c595:37d1:3987:1929>]
rcvd [IPV6CP ConfReq id=0x7b <addr fe80::0221:05ff:feb4:8824>]
sent [IPV6CP ConfAck id=0x7b <addr fe80::0221:05ff:feb4:8824>]
rcvd [IPCP ConfReq id=0×38 <addr 172.16.12.12>]
sent [IPCP ConfAck id=0×38 <addr 172.16.12.12>]
rcvd [IPCP ConfNak id=0×1 <addr 81.146.2.155> <ms-dns1 81.139.57.100> <ms-dns2 81.139.56.100>]
sent [IPCP ConfReq id=0×2 <addr 81.146.2.155> <ms-dns1 81.139.57.100> <ms-dns2 81.139.56.100>]
rcvd [IPV6CP ConfAck id=0×1 <addr fe80::c595:37d1:3987:1929>]
local LL address fe80::c595:37d1:3987:1929
remote LL address fe80::0221:05ff:feb4:8824
Script /lib/netifd/ppp-up started (pid 2646)
rcvd [IPCP ConfAck id=0×2 <addr 81.146.2.155> <ms-dns1 81.139.57.100> <ms-dns2 81.139.56.100>]
local IP address 81.146.2.155
remote IP address 172.16.12.12
primary DNS address 81.139.57.100
secondary DNS address 81.139.56.100
ppp.log
secondary DNS address 81.139.56.100
Script /lib/netifd/ppp-up started (pid 2653)
Script /lib/netifd/ppp-up finished (pid 2646), status = 0×9 Script /lib/netifd/ppp-up finished (pid 2653), status = 0×9

05.11.20171147KernelBug ReportVery LowMediumVLAN problem with MT7530 switchTrunkUnconfirmed Task Description

Device problem occurs on: Xiaomi Mi Router 3G (and I assume anything with a MT7530 switch like the DIR-860L)
Steps to reproduce: When configuring the switch the only way to sync a vlan ID to a port is to have it exactly match the order it occurs in in the config.

I.E If you set up a vlan with ID 3 it has to be the 3rd one in the list in luci.

This means if you were working with VLAN ID in the thousands you’d have to set up thousand of dummy VLAN entries in your config.

Apologies if this has already been reported, there are several posts on the forum, but I didn’t see an actual bug report.

 


09.02.2017487KernelBug ReportVery LowMediumVGV7510KW22 / o2 Box 6431 / RT3062F: Very poor Wi-Fi pe...AllNew Task Description

Actual Wi-Fi performance is abnormally poor and unusually variable, no matter the settings (mode, channels, encryption).

These tests were carried out in quick succession while the LuCI web interface showed a signal strength of -46 - -50 dBm:

[localhost ~]$ iperf3 -c 192.168.1.1
Connecting to host 192.168.1.1, port 5201
[  4] local 192.168.1.171 port 42922 connected to 192.168.1.1 port 5201
[ ID] Interval           Transfer     Bandwidth       Retr  Cwnd
[  4]   0.00-1.00   sec  1.36 MBytes  11.4 Mbits/sec    0   14.1 KBytes       
[  4]   1.00-2.00   sec   964 KBytes  7.90 Mbits/sec    5   11.3 KBytes       
[  4]   2.00-3.00   sec   816 KBytes  6.68 Mbits/sec    4   4.24 KBytes       
[  4]   3.00-4.00   sec   979 KBytes  8.02 Mbits/sec    5   9.90 KBytes       
[  4]   4.00-5.00   sec  1.38 MBytes  11.6 Mbits/sec    0   11.3 KBytes       
[  4]   5.00-6.00   sec  1.24 MBytes  10.4 Mbits/sec    1   9.90 KBytes       
[  4]   6.00-7.00   sec   943 KBytes  7.72 Mbits/sec    2   7.07 KBytes       
[  4]   7.00-8.00   sec  1024 KBytes  8.39 Mbits/sec    7   8.48 KBytes       
[  4]   8.00-9.00   sec  1.11 MBytes  9.29 Mbits/sec    1   9.90 KBytes       
[  4]   9.00-10.00  sec  1.41 MBytes  11.8 Mbits/sec    0   11.3 KBytes       
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bandwidth       Retr
[  4]   0.00-10.00  sec  11.1 MBytes  9.32 Mbits/sec   25             sender
[  4]   0.00-10.00  sec  11.1 MBytes  9.30 Mbits/sec                  receiver

iperf Done.
[localhost ~]$ iperf3 -c 192.168.1.1
Connecting to host 192.168.1.1, port 5201
[  4] local 192.168.1.171 port 42954 connected to 192.168.1.1 port 5201
[ ID] Interval           Transfer     Bandwidth       Retr  Cwnd
[  4]   0.00-1.00   sec   187 KBytes  1.53 Mbits/sec    3   9.90 KBytes       
[  4]   1.00-2.00   sec   638 KBytes  5.22 Mbits/sec    0   11.3 KBytes       
[  4]   2.00-3.00   sec   561 KBytes  4.60 Mbits/sec    0   14.1 KBytes       
[  4]   3.00-4.00   sec   417 KBytes  3.42 Mbits/sec    0   14.1 KBytes       
[  4]   4.00-5.00   sec   307 KBytes  2.51 Mbits/sec    4   8.48 KBytes       
[  4]   5.00-6.00   sec   370 KBytes  3.04 Mbits/sec    2   8.48 KBytes       
[  4]   6.00-7.00   sec   365 KBytes  2.99 Mbits/sec    1   8.48 KBytes       
[  4]   7.00-8.00   sec   281 KBytes  2.30 Mbits/sec    2   1.41 KBytes       
[  4]   8.00-9.00   sec   204 KBytes  1.67 Mbits/sec    8   8.48 KBytes       
[  4]   9.00-10.00  sec   344 KBytes  2.81 Mbits/sec    2   8.48 KBytes       
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bandwidth       Retr
[  4]   0.00-10.00  sec  3.59 MBytes  3.01 Mbits/sec   22             sender
[  4]   0.00-10.00  sec  3.56 MBytes  2.99 Mbits/sec                  receiver

iperf Done.
[localhost ~]$ iperf3 -c 192.168.1.1
Connecting to host 192.168.1.1, port 5201
[  4] local 192.168.1.171 port 42960 connected to 192.168.1.1 port 5201
[ ID] Interval           Transfer     Bandwidth       Retr  Cwnd
[  4]   0.00-1.00   sec   259 KBytes  2.12 Mbits/sec    2   9.90 KBytes       
[  4]   1.00-2.00   sec   923 KBytes  7.57 Mbits/sec    2   11.3 KBytes       
[  4]   2.00-3.00   sec  1.08 MBytes  9.06 Mbits/sec    0   11.3 KBytes       
[  4]   3.00-4.00   sec  1.34 MBytes  11.2 Mbits/sec    2   9.90 KBytes       
[  4]   4.00-5.00   sec   652 KBytes  5.34 Mbits/sec    8   4.24 KBytes       
[  4]   5.00-6.00   sec  1.31 MBytes  11.0 Mbits/sec    1   11.3 KBytes       
[  4]   6.00-7.00   sec  1.37 MBytes  11.5 Mbits/sec    0   15.6 KBytes       
[  4]   7.00-8.00   sec  1.24 MBytes  10.4 Mbits/sec    1   12.7 KBytes       
[  4]   8.00-9.00   sec   683 KBytes  5.59 Mbits/sec    8   9.90 KBytes       
[  4]   9.00-10.00  sec  1.16 MBytes  9.72 Mbits/sec    2   7.07 KBytes       
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bandwidth       Retr
[  4]   0.00-10.00  sec  9.96 MBytes  8.35 Mbits/sec   26             sender
[  4]   0.00-10.00  sec  9.93 MBytes  8.33 Mbits/sec                  receiver

iperf Done.

Confirmed with 17.01.0-rc1, 17.01.0-rc2, SNAPSHOT r3350-aab344d (all NOR images) and different client machines.

On a side note, ethernet performance is also diminished:

[localhost ~]$ iperf3 -c 192.168.1.1
Connecting to host 192.168.1.1, port 5201
[  4] local 192.168.1.161 port 57264 connected to 192.168.1.1 port 5201
[ ID] Interval           Transfer     Bandwidth       Retr  Cwnd
[  4]   0.00-1.00   sec  9.70 MBytes  81.3 Mbits/sec    0    215 KBytes       
[  4]   1.00-2.00   sec  8.96 MBytes  75.2 Mbits/sec    0    215 KBytes       
[  4]   2.00-3.00   sec  9.37 MBytes  78.6 Mbits/sec    4    156 KBytes       
[  4]   3.00-4.00   sec  10.3 MBytes  86.6 Mbits/sec    6    106 KBytes       
[  4]   4.00-5.00   sec  10.4 MBytes  87.0 Mbits/sec    0    161 KBytes       
[  4]   5.00-6.00   sec  8.88 MBytes  74.5 Mbits/sec    2    156 KBytes       
[  4]   6.00-7.00   sec  9.01 MBytes  75.6 Mbits/sec    2    143 KBytes       
[  4]   7.00-8.00   sec  9.47 MBytes  79.5 Mbits/sec    8    140 KBytes       
[  4]   8.00-9.00   sec  10.3 MBytes  86.6 Mbits/sec    6    141 KBytes       
[  4]   9.00-10.00  sec  10.4 MBytes  87.3 Mbits/sec    4    144 KBytes       
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bandwidth       Retr
[  4]   0.00-10.00  sec  96.8 MBytes  81.2 Mbits/sec   32             sender
[  4]   0.00-10.00  sec  96.5 MBytes  80.9 Mbits/sec                  receiver

iperf Done.
16.11.20171173PackagesBug ReportVery LowCriticalustream-ssl Bug ON IPQ806Xlede-17.01Unconfirmed Task Description

LEDE 17.01.4
Kernel 4.9.60
Router: Netgear R7500V2(ARM :IPQ806X)
Packages: Up to Date (2017-11-15)
LuCI works great if Luci-ssl or Luci-openssl is not installed.Once Luci-ssl or Luci-openssl installed with https configuration ,LuCI gets stuck every now and then ,and you`ll have to refresh .When using Firefox ,web crashes and come up with SSL Error: ssl_error_bad_mac_read. Dont know if there is bug in ustream-ssl.


03.06.2017825DocumentationBug ReportVery LowLowUser guide does not mention "config hostrecord" section...TrunkUnconfirmed Task Description

The dhcp configuration file is documented in the user guide at:
https://lede-project.org/docs/user-guide/dhcp_configuration and
https://lede-project.org/docs/user-guide/dns_configuration but neither page mentions the “config hostrecord” section type of the dhcp configuration file. This section type was first proposed here:
https://lists.openwrt.org/pipermail/openwrt-devel/2013-June/020358.html and it was added to openwrt here:
https://dev.openwrt.org/changeset/36943 and it’s in the lede source here:
https://github.com/lede-project/source/blob/master/package/network/services/dnsmasq/files/dnsmasq.init#L658

31.01.2017446Base systemBug ReportVery LowLowusbport trigger: The default configuration for all fami...TrunkUnconfirmed Task Description

Recently LuCI has get ability to configure LED’s with the usbport trigger https://github.com/openwrt/luci/issues/971. There are issues when reading the old usbdev trigger. There is no need to stay with usbdev at all so if it’s possible it should be converted to use usbport.

05.09.2016160Base systemBug ReportVery LowLowusb-serial (pl2303) failures on mt7621 dlink dir860l-b1TrunkUnconfirmed Task Description
git describe
reboot-1497-ga810e77

with diffconfig:

CONFIG_TARGET_ramips=y
CONFIG_TARGET_ramips_mt7621=y
CONFIG_TARGET_ramips_mt7621_DEVICE_dir-860l-b1=y
CONFIG_DEVEL=y
CONFIG_BUILD_LOG=y
CONFIG_PACKAGE_ip=y
CONFIG_PACKAGE_kmod-usb-core=y
CONFIG_PACKAGE_kmod-usb-ohci=y
CONFIG_PACKAGE_kmod-usb-ohci-pci=y
CONFIG_PACKAGE_kmod-usb-serial=y
CONFIG_PACKAGE_kmod-usb-serial-ftdi=y
CONFIG_PACKAGE_kmod-usb-serial-pl2303=y
CONFIG_PACKAGE_kmod-usb2=y
CONFIG_PACKAGE_kmod-usb2-pci=y
CONFIG_PACKAGE_kmod-usb3=y
CONFIG_PACKAGE_screen=y

screen starts, but doesn’t work. The usb-relevant dmesg’s are:

[    4.550000] usbcore: registered new interface driver usbfs
[    4.560000] usbcore: registered new interface driver hub
[    4.570000] usbcore: registered new device driver usb
[    4.580000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.620000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    4.670000] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
[    4.720000] hub 1-0:1.0: USB hub found
[    4.740000] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
[    4.760000] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    4.770000] hub 2-0:1.0: USB hub found
[    5.260000] usb 1-1: new full-speed USB device number 2 using xhci-mtk
[    5.410000] usb 1-1: no of_node; not parsing pinctrl DT
[   10.150000] usbcore: registered new interface driver usbserial
[   10.160000] usbcore: registered new interface driver usbserial_generic
[   10.180000] usbserial: USB Serial support registered for generic
[   10.220000] usbcore: registered new interface driver ftdi_sio
[   10.240000] usbserial: USB Serial support registered for FTDI USB Serial Device
[   10.260000] usbcore: registered new interface driver pl2303
[   10.270000] usbserial: USB Serial support registered for pl2303
[   10.290000] pl2303 ttyUSB0: no of_node; not parsing pinctrl DT
[   10.290000] usb 1-1: pl2303 converter now attached to ttyUSB0
[  871.510000] pl2303 ttyUSB0: pl2303_get_line_request - failed: -145
[  871.620000] pl2303 ttyUSB0: pl2303_set_line_request - failed: -145
[  871.840000] pl2303 ttyUSB0: pl2303_set_control_lines - failed: -145

Screen also throws an error (which gets blanked out, but is captured by the serial console):

# screen /dev/ttyUSB0 115200
/dev/null/utmp: Not a directory
19.02.2017534Base systemBug ReportVery LowHighUSB xHCI deadlock on bootlede-17.01Assigned Task Description

Supply the following if possible:
- Device problem occurs on
VirtualBox x86_64 Version 5.0.32 r112930
- Software versions of LEDE release, packages, etc.
17.01.00rc2
- Steps to reproduce
Create the disk image
Switch from EHCI (the default in a new VM) to xHCI.
Boot the machine
The machine will deadlock soon after initializing the USB ports


02.06.2017823KernelBug ReportVery LowCriticalUSB WIFI dongle TP-LINK TP-WN726N 1.0(rt8188eus) cannot...TrunkUnconfirmed Task Description

Supply the following if possible:
- Device problem occurs on Raspberry Pi 3 Model B Rev 1.2, TP-LINK TP-WN726N 1.0(rt8188eus) USB WIFI dongle
- Software versions of LEDE release, r4297-1893b56 / LuCI Master (git-17.152.36261-b6dd992)
- Steps to reproduce:

 1. Compile rom with rt8xxxu driver and firmware.
 2. Insert TP-LINK TP-WN726N 1.0(rt8188eus) USB WIFI dongle
 3. Boot the system, log is attached.
 4. Type command "cat /ect/config/wireless" in console, TP-WN726N info is listed.
 5. Type command "ifconfig" in console, observe that TP-WN726N is not listed.
 6. Go to Luci web management tool, observe that TP-WN726N is listed, without signal strength. 

- More info:

 TP-LINK TP-WN726N 1.0(rt8188eus) USB WIFI dongle is tested on PC with Ubuntu 16.04, works fine.
20.04.2017726KernelBug ReportVery LowHighUSB not working on TL-WDR4900 v1.xAllUnconfirmed Task Description

USB ports are empty but hub is deteched periodically. Usb ports work abnormal when some devices are inserted.
This bug exists inprevious versions ( in openwrt too).

cat /etc/banner

   _________
  /        /\      _    ___ ___  ___
 /  LE    /  \    | |  | __|   \| __|
/    DE  /    \   | |__| _|| |) | _|

// LE \ ||_|_/|_| lede-project.org
\ \ DE /
\ LE \ / ———————————————————– \ DE \ / Reboot (17.01.1, r3316-7eb58cf109)
\
__\/ ———————————————————–

root@openwrt:~# dmesg | grep -i usb

[ 0.029483] usbcore: registered new interface driver usbfs
[ 0.029537] usbcore: registered new interface driver hub
[ 0.029580] usbcore: registered new device driver usb
[ 2.075954] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.104850] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
[ 2.138024] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
[ 2.144048] hub 1-0:1.0: USB hub found
[ 2.535450] usb 1-1: new high-speed USB device number 2 using fsl-ehci
[ 2.728493] hub 1-1:1.0: USB hub found
[ 3.511480] usb 1-1: USB disconnect, device number 2
[ 3.814034] usb 1-1: new high-speed USB device number 3 using fsl-ehci
[ 3.952117] hub 1-1:1.0: USB hub found
[ 4.484403] usb 1-1: USB disconnect, device number 3
[ 4.730021] usb 1-1: new high-speed USB device number 4 using fsl-ehci
[ 4.868111] hub 1-1:1.0: USB hub found
[ 5.265649] usb 1-1: USB disconnect, device number 4
[ 5.510021] usb 1-1: new high-speed USB device number 5 using fsl-ehci
[ 6.098025] usb 1-1: device not accepting address 5, error -71
[ 6.398018] usb 1-1: new high-speed USB device number 7 using fsl-ehci
[ 6.536098] hub 1-1:1.0: USB hub found
[ 6.844167] usb 1-1: USB disconnect, device number 7
[ 7.110026] usb 1-1: new high-speed USB device number 8 using fsl-ehci
[ 7.706027] usb 1-1: device not accepting address 8, error -71
[ 8.010025] usb 1-1: new high-speed USB device number 10 using fsl-ehci
[ 8.156084] hub 1-1:1.0: USB hub found
[ 8.417000] usb 1-1: USB disconnect, device number 10
..........................
Thu Apr 20 10:41:22 2017 kern.info kernel: [ 961.300660] hub 1-1:1.0: 4 ports detected
Thu Apr 20 10:41:47 2017 kern.info kernel: [ 986.577885] usb 1-1: USB disconnect, device number 124
Thu Apr 20 10:41:47 2017 kern.info kernel: [ 986.821924] usb 1-1: new high-speed USB device number 125 using fsl-ehci
Thu Apr 20 10:41:48 2017 kern.info kernel: [ 986.960029] hub 1-1:1.0: USB hub found
Thu Apr 20 10:41:48 2017 kern.info kernel: [ 986.964202] hub 1-1:1.0: 4 ports detected
Thu Apr 20 10:41:53 2017 kern.info kernel: [ 991.933221] usb 1-1: USB disconnect, device number 125
Thu Apr 20 10:41:53 2017 kern.info kernel: [ 992.177825] usb 1-1: new high-speed USB device number 126 using fsl-ehci
Thu Apr 20 10:41:53 2017 kern.info kernel: [ 992.315980] hub 1-1:1.0: USB hub found
Thu Apr 20 10:41:53 2017 kern.info kernel: [ 992.320159] hub 1-1:1.0: 4 ports detected
Thu Apr 20 10:42:02 2017 kern.info kernel: [ 1001.763764] usb 1-1: USB disconnect, device number 126
Thu Apr 20 10:42:03 2017 kern.info kernel: [ 1002.009660] usb 1-1: new high-speed USB device number 127 using fsl-ehci
Thu Apr 20 10:42:03 2017 kern.info kernel: [ 1002.159774] hub 1-1:1.0: USB hub found
Thu Apr 20 10:42:03 2017 kern.info kernel: [ 1002.163953] hub 1-1:1.0: 4 ports detected
Thu Apr 20 10:42:07 2017 kern.info kernel: [ 1006.033730] usb 1-1: USB disconnect, device number 127
Thu Apr 20 10:42:07 2017 kern.info kernel: [ 1006.281597] usb 1-1: new high-speed USB device number 2 using fsl-ehci
Thu Apr 20 10:42:07 2017 kern.info kernel: [ 1006.419736] hub 1-1:1.0: USB hub found
Thu Apr 20 10:42:07 2017 kern.info kernel: [ 1006.423795] hub 1-1:1.0: 4 ports detected
Thu Apr 20 10:42:10 2017 kern.info kernel: [ 1009.824073] usb 1-1: USB disconnect, device number 2
Thu Apr 20 10:42:11 2017 kern.info kernel: [ 1010.076110] usb 1-1: new high-speed USB device number 3 using fsl-ehci
Thu Apr 20 10:42:11 2017 kern.info kernel: [ 1010.215709] hub 1-1:1.0: USB hub found
Thu Apr 20 10:42:11 2017 kern.info kernel: [ 1010.220010] hub 1-1:1.0: 4 ports detected
Thu Apr 20 10:42:12 2017 kern.info kernel: [ 1011.588932] usb 1-1: USB disconnect, device number 3
Thu Apr 20 10:42:12 2017 kern.info kernel: [ 1011.833503] usb 1-1: new high-speed USB device number 4 using fsl-ehci

cat /sys/kernel/debug/usb/devices

T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 1, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 4.04
S: Manufacturer=Linux 4.4.61 ehci_hcd
S: Product=Freescale On-Chip EHCI Host Controller
S: SerialNumber=fsl-ehci.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms

T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 45 Spd=480 MxCh= 4
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=05e3 ProdID=0608 Rev=85.36
S: Product=USB2.0 Hub
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms

lsusb -v

Bus 001 Device 048: ID 05e3:0608 Genesys Logic, Inc. Hub
Device Descriptor:

bLength                18
bDescriptorType         1
bcdUSB               2.00
bDeviceClass            9 Hub
bDeviceSubClass         0 Unused
bDeviceProtocol         1 Single TT
bMaxPacketSize0        64
idVendor           0x05e3 Genesys Logic, Inc.
idProduct          0x0608 Hub
bcdDevice           85.36
iManufacturer           0 
iProduct                1 USB2.0 Hub
iSerial                 0 
bNumConfigurations      1
Configuration Descriptor:
  bLength                 9
  bDescriptorType         2
  wTotalLength           25
  bNumInterfaces          1
  bConfigurationValue     1
  iConfiguration          0 
  bmAttributes         0xe0
    Self Powered
    Remote Wakeup
  MaxPower              100mA
  Interface Descriptor:
    bLength                 9
    bDescriptorType         4
    bInterfaceNumber        0
    bAlternateSetting       0
    bNumEndpoints           1
    bInterfaceClass         9 Hub
    bInterfaceSubClass      0 Unused
    bInterfaceProtocol      0 Full speed (or root) hub
    iInterface              0 
    Endpoint Descriptor:
      bLength                 7
      bDescriptorType         5
      bEndpointAddress     0x81  EP 1 IN
      bmAttributes            3
        Transfer Type            Interrupt
        Synch Type               None
        Usage Type               Data
      wMaxPacketSize     0x0001  1x 1 bytes
      bInterval              12

Hub Descriptor:

bLength               9
bDescriptorType      41
nNbrPorts             4
wHubCharacteristic 0x00e9
  Per-port power switching
  Per-port overcurrent protection
  TT think time 32 FS bits
  Port indicators
bPwrOn2PwrGood       50 * 2 milli seconds
bHubContrCurrent    100 milli Ampere
DeviceRemovable    0x00
PortPwrCtrlMask    0xff

Hub Port Status:

 Port 1: 0000.0100 power
 Port 2: 0000.0100 power
 Port 3: 0000.0100 power
 Port 4: 0000.0100 power

Device Qualifier (for other device speed):

bLength                10
bDescriptorType         6
bcdUSB               2.00
bDeviceClass            9 Hub
bDeviceSubClass         0 Unused
bDeviceProtocol         0 Full speed (or root) hub
bMaxPacketSize0        64
bNumConfigurations      1

Device Status: 0x0001

Self Powered

Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:

bLength                18
bDescriptorType         1
bcdUSB               2.00
bDeviceClass            9 Hub
bDeviceSubClass         0 Unused
bDeviceProtocol         1 Single TT
bMaxPacketSize0        64
idVendor           0x1d6b Linux Foundation
idProduct          0x0002 2.0 root hub
bcdDevice            4.04
iManufacturer           3 Linux 4.4.61 ehci_hcd
iProduct                2 Freescale On-Chip EHCI Host Controller
iSerial                 1 fsl-ehci.0
bNumConfigurations      1
Configuration Descriptor:
  bLength                 9
  bDescriptorType         2
  wTotalLength           25
  bNumInterfaces          1
  bConfigurationValue     1
  iConfiguration          0 
  bmAttributes         0xe0
    Self Powered
    Remote Wakeup
  MaxPower                0mA
  Interface Descriptor:
    bLength                 9
    bDescriptorType         4
    bInterfaceNumber        0
    bAlternateSetting       0
    bNumEndpoints           1
    bInterfaceClass         9 Hub
    bInterfaceSubClass      0 Unused
    bInterfaceProtocol      0 Full speed (or root) hub
    iInterface              0 
    Endpoint Descriptor:
      bLength                 7
      bDescriptorType         5
      bEndpointAddress     0x81  EP 1 IN
      bmAttributes            3
        Transfer Type            Interrupt
        Synch Type               None
        Usage Type               Data
      wMaxPacketSize     0x0004  1x 4 bytes
      bInterval              12

Hub Descriptor:

bLength               9
bDescriptorType      41
nNbrPorts             1
wHubCharacteristic 0x0009
  Per-port power switching
  Per-port overcurrent protection
  TT think time 8 FS bits
bPwrOn2PwrGood       10 * 2 milli seconds
bHubContrCurrent      0 milli Ampere
DeviceRemovable    0x00
PortPwrCtrlMask    0xff

Hub Port Status:

 Port 1: 0000.0503 highspeed power enable connect

Device Status: 0x0001

Self Powered
20.04.2017727Base systemBug ReportVery LowLowUSB not working on TL-WDR4900 v1.xTrunkUnconfirmed Task Description

USB ports are empty but hub is deteched periodically.

dmesg | grep -i usb
[ 0.029483] usbcore: registered new interface driver usbfs
[ 0.029537] usbcore: registered new interface driver hub
[ 0.029580] usbcore: registered new device driver usb
[ 2.075954] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
[ 2.104850] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
[ 2.138024] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
[ 2.144048] hub 1-0:1.0: USB hub found
[ 2.535450] usb 1-1: new high-speed USB device number 2 using fsl-ehci
[ 2.728493] hub 1-1:1.0: USB hub found
[ 3.511480] usb 1-1: USB disconnect, device number 2
[ 3.814034] usb 1-1: new high-speed USB device number 3 using fsl-ehci
[ 3.952117] hub 1-1:1.0: USB hub found
[ 4.484403] usb 1-1: USB disconnect, device number 3
[ 4.730021] usb 1-1: new high-speed USB device number 4 using fsl-ehci
[ 4.868111] hub 1-1:1.0: USB hub found
[ 5.265649] usb 1-1: USB disconnect, device number 4
[ 5.510021] usb 1-1: new high-speed USB device number 5 using fsl-ehci
[ 6.098025] usb 1-1: device not accepting address 5, error -71
[ 6.398018] usb 1-1: new high-speed USB device number 7 using fsl-ehci

[ 986.577885] usb 1-1: USB disconnect, device number 124
[ 986.821924] usb 1-1: new high-speed USB device number 125 using fsl-ehci
[ 986.960029] hub 1-1:1.0: USB hub found
[ 991.933221] usb 1-1: USB disconnect, device number 125
[ 992.177825] usb 1-1: new high-speed USB device number 126 using fsl-ehci
[ 992.315980] hub 1-1:1.0: USB hub found
[ 1001.763764] usb 1-1: USB disconnect, device number 126
[ 1002.009660] usb 1-1: new high-speed USB device number 127 using fsl-ehci
[ 1002.159774] hub 1-1:1.0: USB hub found
[ 1006.033730] usb 1-1: USB disconnect, device number 127
[ 1006.281597] usb 1-1: new high-speed USB device number 2 using fsl-ehci
[ 1006.419736] hub 1-1:1.0: USB hub found
[ 1009.824073] usb 1-1: USB disconnect, device number 2
[ 1010.076110] usb 1-1: new high-speed USB device number 3 using fsl-ehci

cat /sys/kernel/debug/usb/devices

T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 1, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 4.04
S: Manufacturer=Linux 4.4.61 ehci_hcd
S: Product=Freescale On-Chip EHCI Host Controller
S: SerialNumber=fsl-ehci.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms

T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 88 Spd=480 MxCh= 4
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=05e3 ProdID=0608 Rev=85.36
S: Product=USB2.0 Hub
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms

lsusb -v

Bus 001 Device 090: ID 05e3:0608 Genesys Logic, Inc. Hub
Device Descriptor:

bLength                18
bDescriptorType         1
bcdUSB               2.00
bDeviceClass            9 Hub
bDeviceSubClass         0 Unused
bDeviceProtocol         1 Single TT
bMaxPacketSize0        64
idVendor           0x05e3 Genesys Logic, Inc.
idProduct          0x0608 Hub
bcdDevice           85.36
iManufacturer           0 
iProduct                1 USB2.0 Hub
iSerial                 0 
bNumConfigurations      1
Configuration Descriptor:
  bLength                 9
  bDescriptorType         2
  wTotalLength           25
  bNumInterfaces          1
  bConfigurationValue     1
  iConfiguration          0 
  bmAttributes         0xe0
    Self Powered
    Remote Wakeup
  MaxPower              100mA
  Interface Descriptor:
    bLength                 9
    bDescriptorType         4
    bInterfaceNumber        0
    bAlternateSetting       0
    bNumEndpoints           1
    bInterfaceClass         9 Hub
    bInterfaceSubClass      0 Unused
    bInterfaceProtocol      0 Full speed (or root) hub
    iInterface              0 
    Endpoint Descriptor:
      bLength                 7
      bDescriptorType         5
      bEndpointAddress     0x81  EP 1 IN
      bmAttributes            3
        Transfer Type            Interrupt
        Synch Type               None
        Usage Type               Data
      wMaxPacketSize     0x0001  1x 1 bytes
      bInterval              12

Hub Descriptor:

bLength               9
bDescriptorType      41
nNbrPorts             4
wHubCharacteristic 0x00e9
  Per-port power switching
  Per-port overcurrent protection
  TT think time 32 FS bits
  Port indicators
bPwrOn2PwrGood       50 * 2 milli seconds
bHubContrCurrent    100 milli Ampere
DeviceRemovable    0x00
PortPwrCtrlMask    0xff

Hub Port Status:

 Port 1: 0000.0100 power
 Port 2: 0000.0100 power
 Port 3: 0000.0100 power
 Port 4: 0000.0100 power

Device Qualifier (for other device speed):

bLength                10
bDescriptorType         6
bcdUSB               2.00
bDeviceClass            9 Hub
bDeviceSubClass         0 Unused
bDeviceProtocol         0 Full speed (or root) hub
bMaxPacketSize0        64
bNumConfigurations      1

Device Status: 0×0001

Self Powered

Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:

bLength                18
bDescriptorType         1
bcdUSB               2.00
bDeviceClass            9 Hub
bDeviceSubClass         0 Unused
bDeviceProtocol         1 Single TT
bMaxPacketSize0        64
idVendor           0x1d6b Linux Foundation
idProduct          0x0002 2.0 root hub
bcdDevice            4.04
iManufacturer           3 Linux 4.4.61 ehci_hcd
iProduct                2 Freescale On-Chip EHCI Host Controller
iSerial                 1 fsl-ehci.0
bNumConfigurations      1
Configuration Descriptor:
  bLength                 9
  bDescriptorType         2
  wTotalLength           25
  bNumInterfaces          1
  bConfigurationValue     1
  iConfiguration          0 
  bmAttributes         0xe0
    Self Powered
    Remote Wakeup
  MaxPower                0mA
  Interface Descriptor:
    bLength                 9
    bDescriptorType         4
    bInterfaceNumber        0
    bAlternateSetting       0
    bNumEndpoints           1
    bInterfaceClass         9 Hub
    bInterfaceSubClass      0 Unused
    bInterfaceProtocol      0 Full speed (or root) hub
    iInterface              0 
    Endpoint Descriptor:
      bLength                 7
      bDescriptorType         5
      bEndpointAddress     0x81  EP 1 IN
      bmAttributes            3
        Transfer Type            Interrupt
        Synch Type               None
        Usage Type               Data
      wMaxPacketSize     0x0004  1x 4 bytes
      bInterval              12

Hub Descriptor:

bLength               9
bDescriptorType      41
nNbrPorts             1
wHubCharacteristic 0x0009
  Per-port power switching
  Per-port overcurrent protection
  TT think time 8 FS bits
bPwrOn2PwrGood       10 * 2 milli seconds
bHubContrCurrent      0 milli Ampere
DeviceRemovable    0x00
PortPwrCtrlMask    0xff

Hub Port Status:

 Port 1: 0000.0503 highspeed power enable connect

Device Status: 0×0001

Self Powered


12.07.2017901Base systemBug ReportVery LowLowUSB not working on MikroTik hAP ac TrunkUnconfirmed Task Description

Only affecting hAP ac / RB962UiGS-5HacT2HnT

Tested with LEDE trunk in April, no relevant commits to device since.

GPIO to control USB power works, and USB controller appears in dmesg on boot. Upon connecting any device, it is not recognised and there are no kernel messages. Same devices work (albeit via internal hub) on Archer C7 v2 using same SoC.

Bug independently verified by another user, not a hardware defect with a single unit.

I am aware of the irony that I contributed the support for this device, and reported USB as working. I was only looking for the controller to be recognised and neglected to test with an actual USB device until after this was merged. My bad. Logging as a bug so that anyone who finds it not working can at least see a record and know to direct their blame towards me :)

28.03.2017661Base systemBug ReportVery LowHighUSB hostless modem is not detected during boot - HooToo...lede-17.01Unconfirmed Task Description

After flashing my HooToo HT-TM02 with LEDE 17.01 I noticed that my hostless modem
ZTE MF823 is not detected when attached during boot. lsusb or cat /sys/kernel/debug/usb/devices
just shows nothing. Also dmesg is logging nothing regarding the device during boot.
If the modem is hotplugged, everything works fine. Same behaviour in OpenWRT Chaos Chalmer.

Tried unloading and reloading all usb related modules with no success. No detection at all.
Only unplugging and replugging helps. If the modem is detected after replugging, a
router reboot will detect it properly. A reboot without a forced detection via replugging leads to
no detection. Powering the router down, also results in no detection after rebooting.

If attached to a “non powered” USB-Hub it gets detected during boot, so no power issue here.

And the modem works perfekt after boot on a WD MyNet 600 with LEDE 17.01. So i think it’s a
platform related issue handling the usb modules.

Hope there is enough info for someone to find the bug.

THX.

Showing tasks 1 - 50 of 375 Page 1 of 81 - 2 - 3 - 4 - 5 - Last >>

Available keyboard shortcuts

Tasklist

Task Details

Task Editing